manualshive.com logo in svg

Motorola 56F8323, User Manual

Share
Download
Motorola 56F8323 User Manual Download Page 9

MOTOROLA

Preface

vii

Preface

This reference manual describes in detail the hardware on the 56F8323 Evaluation 
Module. 

Audience

This document is intended for application developers who are creating software for 
devices using the Motorola 56F8323 part.

Organization

This manual is organized into two chapters and two appendixes.

•

Chapter 1, Introduction - 

 

provides an overview of the EVM and its features

.

•

Chapter 2, Technical Summary - 

 describes in detail the 56F8323EVM hardware.

•

Appendix A,"56F8323EVM Schematics"

 contains the schematics of the 

56F8323EVM.

•

Appendix B, 56F8323EVM Bill of Material - 

 provides a list of the materials used on the 

56F8323EVM board

.

Suggested Reading

More documentation on the 56F8323 and the 56F8323EVM kit may be found at URL:

www.motorola.com/semiconductors

 

   

  

F

re

e

sc

a

le

 S

e

m

ic

o

n

d

u

c

to

r,

 I

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

 

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

n

c

.

..

Summary of Contents for 56F8323





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands