Motorola 49901 - Vanguard 340 Router Instruction Manual Download Page 98

Page: 98 / 121

Power Up
Sequence

When the Vanguard 340 and 340 Enhanced power cord is plugged into the power
supply outlet, you will see the following power up sequence:

Detailed FT1/FE1
LED

The FT1/FE1 daughtercards have one LED located on the rear panel. Software
controls the LED and indicates the following when ON or OFF:

• ON - Alarm condition data path is disrupted, refer to the FT1/FE1 interface

statistics for more information on the problem.

• OFF - Normal operation exists.

Stage

when...

...this indicates

Power (PWR) LED turns on
(GREEN)

Vanguard is receiving power.

PWR LED remains on and the
Status (STAT) LED blinks
(RED).

Diagnostics are starting.

PWR LED blinks.

Diagnostics are executed.

PWR LED remains on and the
STAT LED blinks.

Indicates software is being
downloaded from FLASH.

PWR LED blinks.

Software is initializing your system
configuration.

PWR LED remains on.

Your system is running.

Summary of Contents for 49901 - Vanguard 340 Router


























































































































Search results

Summary of Contents for 49901 - Vanguard 340 Router

Reviews:

Related manuals for 49901 - Vanguard 340 Router

Brands by name

Popular brands

Motorola 49901 - Vanguard 340 Router, Instruction Manual

Search results

Summary of Contents for 49901 - Vanguard 340 Router

Reviews:

Related manuals for 49901 - Vanguard 340 Router

Brands by name

Popular brands