Mostec M2118 Operating Manual Download Page 3

 

M2118

 

Operating Manual

 

 

V1.06 © 17.10.2011 MOSTEC  AG, CH-4410 Liestal 

3

 

Index:

 

Page  

 

A  Front panel controls 

B  Adjusting the limit contacts with two programming buttons/ handling access codes 

3/4 

C   Adjusting the limit contacts with programming software  

D   Adjusting the display range with programming software  

E  Adjusting a tare value 

F   Adjusting the output signal range with programming software  

5  

G   Fine-adjust the display/current output with the programming buttons 

6  

H   Fine-adjust the display with programming software  

6  

I   General references for using the programming software  

6  

J   Technical data   

7  

K   User menu 

 

 

A. Font panel controls 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

B. Adjusting the limit contacts with two programming buttons 

 

The value of the limit contacts can be changed by two buttons without programming Software. 
 

1. Unlock the user menu / insert or modify the menu protection access code:

 

The values of the user menu can be protected from unintended access using an access code. After activating the 
access code, menu values can be observed but no longer modified. To modify setpoints and other parameters, the 
access code has to be set to the value 0000. If the code has a value different from 0000, writing to the user menu is 
suppressed. 
 

Set the access code: 

 

1.  Press and hold both buttons <ENTER> und <ESC> for 4 seconds. 

 

  

ð

 After 4 seconds The display shows SP_1 indicating the user menu. 

2.  Now navigate to the Code menu item with the button <->, then press <ENTER>. 
 

a) A code has already been entered:

 The display flashes between Code und 0. Enter now the valid access 

code with the buttons <+> and <-> and confirm with the  <ENTER> key. If the code is wrong, the instrument 
quits the user menu (in case you do not know your code any more, call MOSTEC we have a unlock code). If 
the code is correct, it can be modified with the keys <+> and <->, or in order to make changes to the user 
menu, set to 0000. 
 

b) No code has been entered: 

The display shows 0000. A code can be entered with the keys <+> and <-> 

then confirm with the <ENTER> key. If you do not need the user menu protection, leave the value 0000 
unchanged and quit the code menu with the <ESC> key. 

progamming adapter 

 

<+> / SP1 

<-> / SP2 

 

ESC /Temp 

 

ENTER / Setup 

 

Summary of Contents for M2118









Reviews: