manualshive.com logo in svg

Mosa DSP 400 YSX, Use And Maintenance Manual

Share
Download
Mosa DSP 400 YSX Use And Maintenance Manual Download Page 17

TRANSPORT AND DISPLACEMENTS COVERED UNITS

GE_, MS_, TS_

M

4

© MOSA

1.0-03/00

NOTE

In case you should transport or move the machine, keep to the instructions as per the figures.
Make the transportation when the machine has 

no

 petrol in its tank, 

no

 oil in the engine and and electrolyte in the

battery.
Be sure that the lifting devices are: correctly mounted, adequate for the weight of the machine with it’s packaging, and
conform to local rules and regulations.
Only authorized persons involved in the transport of the machine should be in the area of movement.

DO NOT LOAD OTHER PARTS WHICH CAN MODIFY WEIGHT AND BARICENTER POSITION.
IT IS STRICTLY FORBIDDEN TO DRAG THE MACHINE MANUALLY OR TOW IT BY ANY VEHICLE (model with no
CTL accessory).

If you did not keep to the instructions, you could damage the structure of the machine.

DANGER: 

LIFTING EYE IS NOT DESIGNED TO SUPPORT

ADDED WEIGHT OF ROAD TOW TRAILER

DO NOT LIFT THE MACHINE AND TRAILER

LIFT ONLY THE MACHINE

30/03/00  M4GB

Summary of Contents for DSP 400 YSX



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands