background image

20/07/16 M20 (raf

f_aria)_EN

ENGLISH

ENGLISH

ATTENTION

It is dangerous to supply too much lube oil to the engine 

because a sudden increase in engine rpm could be caused 

by its combustion.

!

REV
.2-10/16

M

20

SET-UP FOR OPERATION

(DIESEL ENGINE)

AIR COOLED SYSTEMS

DRY AIR FILTER

Check that the dry air filter is correctly installed and that there 

are no leaks around the filter which could lead to infiltrations of 

non-filtered air to the inside of the motor.

FUEL

ATTENTION

Stop engine when fueling. Do not smoke or use 

open flames during refuelling operations, in order 

to avoid explosions or fire hazards.

Fuel fumes are highly toxic; carry out operations 

outdoors only, or in a well-ventilated environment. 

Avoid accidentally spilling fuel. Clean any even-

tual leaks before starting up motor.

!

BATTERY WITHOUT MAINTENANCE

(WHERE IT IS ASSEMBLED)

The supplied battery is generally ready for use.

Connect the cable + (positive) to the pole + of the battery, by 

properly tightening the clamp.

In some models the battery should be activated.

To activate it (fill the included acid) please follow the instructions 

shown on the manual attached to the battery. When battery is 

activated, 

DON’T

 add any other liquid.

OIL BATH AIR FILTER

Fill the air filter using the same engine oil up to the level indi

-

cated on the filter.

LUBRICANT

Please refer to the motor operating manual for the recommen-

ded viscosity.

Oil filling and level ispections must be carried out with the engine 

on a flat surface:

1.  Remove oil filler cap (24);

2.   Pour the oil in and reassemble oil cap;

3.  Check the oil level using the dipstick (23); the oil level must 

be comprised between the minimum and maximum indicators.

Refill the tank with good quality diesel fuel, such as automobile 

type diesel fuel, for example. 

For further details on the type of diesel fuel to use, see the motor 

operating manual supplied.

Do not fill the tank completely; leave a space of approx. 10 

mm between the fuel level and the wall of the tank to allow for 

expansion.

In  rigid  environmental  temperature  conditions,  use  special 

winterized diesel fuels or specific additives in order to avoid 

the formation of paraffin.

ATTENTION

A  qualified  electrician  should  carry  out  electrical  connec

-

tions according to the norms in force.

ELECTRICAL CONNECTIONS

The electrical connection to the User system is a very impor-

tant operation: safety and good operation of the genset and 

User system depend on a correct electrical connection.

Before supplying User system always check:

• 

that wires connecting gen-set to the user plant  are suitable 

to the supplied voltage and are in accordance to the appli-

cable rules;

• 

wire type, section and length have been calculated consi

-

dering environment conditions and in force norms;

• 

ground is functioning correctly: earth fault relay device wor

-

ks only if this connection is operating;

•  that direction of the phases corresponds to  the user plant 

phase rotation, and none of the phases has been acciden

-

tally connected to neutral.

!

19

Summary of Contents for CD4R90119003





































Reviews: