background image

www.morsona.com

[ 4 ]

[ 5 ]

Please read the entire installation and operation manual before you install and use your new solid fuel 

heater. If this appliance is not properly installed, a house fire may result. To reduce the risk of fire, ca-

refully follow the installation instructions. Failure to follow instructions may result in 

property damage, 

bodily injury, or even death.

Contact local building or fire officials about restrictions and installation inspection requirements

in your area. Save these instructions for future reference.

MORSØ JERNSTØBERI A/S . DK-7900 NYKØBING MORS, Denmark

E-Mail: [email protected] • Website: www.morsoe.com

Tested and listed by OMNI-Test Laboratories, Inc, Portland Oregon.

Tested to U.S. Standards ANSI/UL-1482 and Canadian Standards ULC S627

The heater is listed for burning wood only. Do not burn other fuels.

Standards

The Morsø 7600-series meets the U.S. Environmental Protection Agency’s emission limits for wood 

heaters sold on or after July 1, 1990 (EPA Phase 2)

The Morsø 5660 Standard Insert has been tested by OMNI-Test Laboratories, Inc. The test standards 

are ANSI/UL-1482 for the United States and ULC S627 for Canada.

The heater is listed for burning wood only. Do not burn other fuels

Under specific test conditions this heater has been shown to delivery heat at rates ranging from 10,875 

to 21,267 Btu/hr.

Always check Local Building Codes

When installing or operating your Morsø heater always follows the instructions detailed within this 

manual. Please store in a safe place and make them available to any person who requires it for future 

inspection or servicing. 

A building permit may be needed to install a solid fuel heater in your locality. In the US, Standard 

NFPA211 may apply, in Canada CAN/CSA-B365-M93 may apply. For clarification consult your local 

building inspector.

Safety Notices & Standards

Safety Notice

Table of Contents

• 

Technical Specifications 

2

SAFeTy NOTiCeS & STANDArDS 

5

• 

Safety Notice 

5

• 

Standards 5

• 

Safety Notices 

6

iNSTALLATiON 7

• 

Preparation 7

• 

The chimney / flue system 

7

• 

Clearances to combustible surfaces 

13

• 

Floor Protection 

15

• 

Mobile Home Installation 

16

OperATiON 18

• 

Choosing your fuel 

18

• 

How to light your stove 

20

MAiNTeNANCe 23

• 

Ceramic glass replacement 

24

• 

Internal Parts 

25

 

- Removing the baffle assembly 

25

 

- Door Rope Gasket 

25

 

- Cleaning the Heater and the Chimney Connector 

25

 

- Ash disposal 

25

• 

Chimney sweeping & inspection 

26

WOrDS OF WiSDOM 

27

SpAre pArTS 

28

Summary of Contents for 7642


















Reviews: