background image

www.morsona.com

[ 2 ]

[ 3 ]

Welcome to Morsø …….

Thank you and congratulations on the purchase of your new Morsø heater.

Morsø has been at the forefront of cast iron wood heater design since 1853. Each and every heater is 

hand built by skilled crafts-people using the best materials available. However, to extract the best per-

formance, warmth and comfort from your heater it is essential all the installation requirements detailed 

within this manual are met. Please take the time to read this manual cover to cover before installation.

Optional Accessories

Morsø offers a comprehensive selection of accessory products (fire tools, fuel buckets) that extends 

Form & Function to the hearth. A wide range of maintenance products is also available to keep your new 

Morsø heater in tip-top condition.

For optimum use of your Morsø heater we highly recommend using the 

Morsø Wood Moisture Meter

 to 

ensure good fuel quality as well as the 

Morsø Stove Thermometer 

that indicates the correct operating 

temperature.

Morsø 7600-series was designed by Monica Ritterband, currently one of Denmark’s 
most sought-after designers. Monica Ritterband is known for her pioneering designs, 
which all take their starting point in her unique universes and totally special, organic 
language of form and lines. Thus, the Morsø 7600 was also created in this way – it is 
completely unique with its circular form, round feminine transitions and its huge glass 
window, the biggest in Morsø’s history of stoves.

Morsø 7642

Morsø 7648

Morsø 7644

Technical Specifications

Maximum Heat   

 

35,000 BTU/hr

Heat output range (Lab test)  

10,875-21,267 BTU/hr

Test fuel load 

 

 

6 lbs

Particulate Emission 

 

4.4 grm/hr

Log 

size    

11”

Max. Area Heated  

 

1200 ft2

Firebox Dimensions 

 

13” W x 10½” D

Firebox volume/capacity 

 

0.85 ft3

Efficiency rating (as measured by LHV) 

75%+

IRS Tax Credit (under American Recovery and

Reinvestment Act of 2009)   

Eligible

Outside air supply  

 

Available

Mobile home approved 

 

Yes

Washington State  

 

Compliant

Basic Clearance (using single wall pipe top vent)

Stove to side wall  

 

15”

Stove to rear wall  

 

1”

Stove to corner   

 

2½”

See installation manual for other configurations

                         Features 

Danish Design and Function

Finest Cast Iron construction

Chrome iron internal castings

Pre-heated clean-glass system

Non-catalytic combustion system

Convection Heater

Reversible flue collar

Vermiculite lining

Ashpan

10-Year Limited Warranty

Low smoke emissions

Made from 98% recycled iron

Recycled packaging

EPA Approved

Summary of Contents for 7642


















Reviews: