The Specialist In Drum Handling Equipment
Model 400AM-60
Hydra-Lift, 60”, with Spark Resistant Parts,
Manual Lift & Tilt
Operator’s Manual for Morse Hydra-Lift Karrier Model 400AM-60
with Serial Number 0414 to ____ (MMYY)
morsedrum.com
Copyright 2019 - Morse Mfg. Co., Inc. Form OM400AM-60 (0414-____)
(Updated 12 Jun, 2019 11:34 AM)
6
Operating Instructions
Push the Hydra-Lift Karrier to the drum.
1.
Using the “LIFT” control as described in “Machine Description
2.
- Controls” (page 3) , position the drum holder assembly with
the back band at the middle of the drum. (Figure 3.1). With
the ratchet plate swung open and the cinch chain hanging
from the chain hook, push the unit until the back band rests
firmly against the drum. Some adjustment to the tilt angle of
the saddle may be necessary to ensure band fits flush on the
drum.
Attaching the drum: Drape the chain across the front of the
3.
drum and engage a link into the slot in the ratchet (Figure
3.2). Turn the ratchet clockwise to tighten chain. If ratchet
turns until the pawl is beyond the last ratchet tooth, turn the
ratchet back and slide the next link into the ratchet slot and try
tightening again. The chain must be held tightly against the
drum with the pawl engaged securely in the ratchet teeth.
Operate the lift function to lift drum clear of floor. Roll to
4.
dispensing location. NOTE: Do not allow the drum to impact
on floor, pouring station, etc. or a spill or damage could occur.
5.
CAUTION
– Do Not Transport with Drum Raised
ALWAYS LOWER THE DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING.
The unit can become unstable when transporting with a raised load.
Lift drum to desired pouring height. Operate the tilt control as described in
6.
“Machine Description - Controls”
(page 3) to adjust the
drum attitude. This is especially important when lifting an open drum. The floor lock should be engaged while dispensing / draining.
When dispensing is complete, tilt drum back to upright position. Disengage the floor lock and lower the drum to transporting height;
7.
about 6” off the floor.
WARNING
- Stay Clear of Raised Drum
NEVER allow anyone to be below any part of a raised drum handler or drum. Remain behind the
push handle while handling a drum.
WARNING
– Do NOT Disengage the Cinch Chain When Drum is off the Ground
When the drum is in the upright position, lower the drum to the floor before releasing the cinch chain.
Push the unit to the drum storage area and lower to the floor in an upright position. Release the cinch chain from the ratchet by
8.
applying pressure to the ratchet handle in a clockwise direction with one hand and opening the pawl to free the ratchet with the other
hand. Remove the cinch chain link from the ratchet.
Maintenance
Periodic inspection for the general condition of structural and mechanical components is imperative for safe and efficient operation.
•
Periodically inspect all moving parts, framework, and contact areas for signs of wear, fatigue, or loosening. Tighten, adjust, or
•
replace parts as necessary to prevent failure and maintain proper function.
Inspect the hydraulic system for oil drips, hose damage, or other signs of wear. Inspect the level and condition of the hydraulic fluid.
•
Replace any parts that show signs of wear.
Grease wheel bearings periodically. Oil or grease all moving parts including: the three clevis pins and the surfaces of the boom which
•
contact the inside of the mast cap, the hinge pin, the gears and sprockets in the tilt drive, and the ratchet and pawl.
Worn or damaged parts must be properly replaced with the correct, genuine Morse parts.
•
Hydraulic pump should be filled with the provided quart of Mobil ATF D/M (Morse part # 3983-P). Material safety data sheet (MSDS)
•
is available online. Change oil yearly, sooner depending on dirty conditions or outdoor use.
Figure 3.2
