14
Maintenance
Auto-clean descale function
9
Each time approximately 5L of water has been used in the steam
generator, it will need to run an auto-clean cycle. When the product
is fully cooled down and first switched on, it will draw water from the
detachable water tank (11) to flush the boiler, emptying dirty water
and limescale into the dirty water chamber (2). For this short time,
the descale indicator (19) will flash and you will be unable to use
the product to iron.
If there is not sufficient water to operate this function, the product
will alert you with the low water indicator (20) and the process will
be paused until the tank is refilled and replaced.
WARNING: During the auto-clean process, the water ejected
from the machine is very hot, so do not remove the water tank
until the auto-clean process is finished.
The auto-clean process will take approximately 3 minutes, after
which the steam generator will be ready for normal operation again.
The flashing descale indicator (19) will extinguish and the low
steam level indicator (24a) will flash, indicating that the steam
generator is readying itself for the low steam level setting.
After ironing, switch off the steam generator at the On/Off power
button (22) and unplug from the mains outlet. If the auto-clean
function has activated and completed, wait for the steam generator
to cool down completely. Remove the detachable water tank and tip
the dirty water from the dirty water emptying hole (3).
10
IMPORTANT: Ensure the dirty water is emptied after each
auto-clean cycle to prevent overflow.
WARNING: Dirty water in the dirty water chamber (2) will be
hot after the auto-clean process, so take care when pouring it
out.
To clean a ceramic soleplate
Do not use scouring powder or solution as this could cause
damage to the coating.
If any man made fibres fuse to the soleplate (5), pass it over a
clean piece of cotton to draw the deposit off the surface.
To clean the exterior
Allow the unit to cool and wipe over with a damp cloth and mild
detergent, then wipe dry.
Emptying and storing
11 12
Allow the appliance to cool.
Remove the detachable water tank (11) by pulling the water tank
handle (10). Empty the water tank. Once the water tank is empty,
re-attach it to the base unit (16).
Wrap the power cord and steam supply cord loosely in long loops.
Gently push the looped cords along the cord storage groove (17)
into the cord storage (18) areas on either side of the base unit (16),
one cord per side. Avoid kinking of cables, particularly where they
meet the base unit.
WARNING: To avoid internal damage, do not squeeze the
cables where folded. Do not pull too tightly on the steam
supply cord or on the cable support (9) when looping the
power cord and steam supply cord. Damage to cables caused
by wrapping too tightly will not be covered by the guarantee.
Storing the steam iron
13
Lock the iron into the storage position on top of the base unit (16)
by sliding the tip of the soleplate (5) under the iron locking hook
(12). With the lower end of the soleplate in position adjacent to the
lower end of the iron rest plate (13), slide the iron-to-base lock (8)
to the position marked with a padlock icon - this secures the
soleplate in place. Once the iron-to-base lock is locked securely,
the iron can be carried by the iron handle (7).
Contact us
Helpline
If you are having a problem with your appliance, please call our
Helpline, as we are more likely to be able to help than the store
you purchased the item from. Please have the product name,
model number and serial number to hand when you call to help
us deal with your enquiry quicker.
UK Helpline:
0344 871 0944
IRE Helpline:
1800 409 119
Spares:
0344 873 0710
Talk To Us
If you have any questions or comments, or want some great tips
to help you get the most out of your products, join us online:
Blog:
www.morphyrichards.co.uk/blog
Facebook:
www.facebook.com/morphyrichardsuk
Twitter:
@loveyourmorphy
Website:
www.morphyrichards.com
RN332103MEE Rev2.qxp_Morphy Richards Instruction Book 25/08/2021 14:39 Page 14
