background image

www.goblin-vacuums.com

Bagless upright vacuum cleaner

Please read and keep these instructions

VC73285 MUK Rev 2

For replacement parts, help with using your Goblin vacuum,

problems and lots more, contact us by phone or through our website.

UK Helpline: 0844 871 0949 

Replacement Parts: 0844 873 0715

Ireland Helpline: 1800 409 119

Getting the best from your new cleaner...

If your cleaner is not picking up as well as it should, please check:

Dust canister

It is important to regularly empty the canister, even if it does not appear full.  

Filters 

It is important that the dust canister pleated/mesh filter is tapped clean over a
dustbin each time the dust canister is emptied, this allows air through the appliance.
Wash the canister filters regularly in luke-warm water and allow to air dry before
re-fitting.

Blockages

Check the hose, tubes and tools for blockages.

Safety cut-out

If the air-flow is blocked or the filters are not regularly cleaned, a thermostat may operate.
If this happens, switch off and disconnect from the mains supply. Clear any blockage,
empty and clean the filters. Allow 60 minutes for the thermostat to reset.

Belt

If the brush-bar is not rotating, check the belt (as described on page 6). Replace any
damaged or broken belts.

Upon registration with Morphy Richards

(UK & ROI only)

Register online for your 2 year

guarantee. See back of this

instruction book for details.

(UK and Ireland customers only)

www.goblin-vacuums.com

VC73285MUK Rev2:VC73285MUK Rev2  19/01/2010  09:40  Page 1

Summary of Contents for 73285 BAGLESS UPRIGHT VACUUM CLEANER









Reviews: