manualshive.com logo in svg

Morningstar TS-MPPT-60-600V-48-DB-TR, Installation, Operation And Maintenance Manual, Page: 10 / 45

Share
Download
Morningstar TS-MPPT-60-600V-48-DB-TR Installation, Operation And Maintenance Manual Download Page 10

19

 

 TriStar MPPT-600V-TR Operator's Manual

18

 Installation

3.1 General Information

WARNING:  Equipment Damage or Risk of Explosion

Never install the TS-MPPT-600V-TR in an enclosure with vented/flooded batteries. 

Battery fumes are flammable and will corrode and destroy the TS-MPPT-600V-TR 

circuits.

!

CAUTION:  Equipment Damage

When installing the TS-MPPT-600V-TR in an enclosure, ensure sufficient ventilation. 

Installation in a sealed enclosure will lead to over-heating and a decreased product 

lifetime.

AVERTISSEMENT:  Endommagement de l’équipement ou risque d’explosion

N’installez jamais le TS-MPPT-600V-TR dans une enceinte avec des batteries à évent/à 

électrolyte liquide. Les vapeurs des batteries sont inflammables et corroderont et 

détruiront les circuits du TS-MPPT-600V-TR.

!

PRUDENCE:  Endommagement de l’équipement 

Assurez une ventilation suffisante en cas d’installation du TS-MPPT-600V-TR dans une 

enceinte. L’installation dans une enceinte hermétique entraîne une surchauffe et une 

réduction de la durée de vie du produit.

 

          

WARNING:

  

Installation must comply with all US  National Electrical Code and Canadian Electrical Code  

 

 

requirments.  Breakers and fuses may require lower ratings than referenced below, so as not to exceed   

 

             any specific wire ampacity.

  

           Avertissement :   

Installation doit être conforme aux tous les États-Unis National Electrical Code et  

 

           Code canadien d'électricité requirments. Disjoncteurs et fusibles peuvent nécessiter des cotes                 

 

            inférieures que référencé ci-dessous, de manière à ne pas dépasser n'importe quel fils particulier              

                         admissible.

The installation is straight-forward, but it is important each step is done correctly and safely.  A 

mistake can lead to dangerous voltage and current levels.  Be sure to carefully follow each        

instruction in this section. 

READ ALL INSTRUCTIONS FIRST

 before beginning installation.

The installation instructions are for installation of a negative grounded system. U.S National 

Electrical Code (NEC) requirements are noted on occasion for convenience, however the          

installer should have a complete understanding of NEC and UL requirements for photovoltaic             

installations.
Solar and battery fuses or DC breakers are required in the system.  These protection devices 

are external to the TS-MPPT-600V-TR controller, and must be 90 amps or lower for the 60 amp 

TS-MPPT-600V-TR.
Maximum battery short-circuit current rating must be less than the interrupt current rating of the 

battery over-current protection device referenced above.
Stranded wires to be connected to the TS-MPPT-600V-TR terminals should be prepared first 

with e.g. clamped copper heads, etc. to avoid the possibility of one conductor free out of the          

connection screw, and possible contact with the metal enclosure.

 Installation

3.0

Recommended Tools:

•  Wire strippers
•  Wire cutters
•  #2 & #0 Phillips screwdriver
•  slotted screwdrivers

•  Pliers
•  Drill3/32” (2.5 mm) drill bit
•  Level
•  hack saw (cutting conduit)

3.2 Wiring Zones 

The 600V solar circuits must be separated from the low voltage battery circuits and 

communication wiring within the wiring box. Figure 3-1 below shows the high voltage and low 

voltage zones (shaded) within the wiring box. There is overlap in the zones as pictured because 

the removable wiring divider separates the high voltage solar wiring and low voltage wiring. Solar 

high voltage wiring should be routed below the removable wiring divider.  The yellow 

Solar 

Terminal Bridge

 must be properly fitted in place before making the solar power terminal 

connections. 

 

The battery wiring and all communication cables must only be routed within the low voltage     

wiring zone. After the solar wiring is installed, the wiring divider should be secured in place, and 

the battery cables routed above the divider. Detailed installation steps are provided in the 

following sections.

 

NOTE:

  

If ALL  field wiring, including communications cable, is rated for 600V, wiring zone separation is   

                 not required.  In this case, it may be more convenient to remove the  high-low voltage wiring box divider,  

                 and terminate conduit that contains mixed voltage  conductors at one point.

                 REMARQUE:

  

Si tout câblage, y compris câble de communication, est évalué à 600V, câblage zone  

                 séparation est non requis. Dans ce cas, il peut être plus pratique d'enlever le diviseur de boîte câblage de    

                 tension haut/bas, et fin des conduits contenant des conducteurs mixtes de tension à un moment donné.

Summary of Contents for TS-MPPT-60-600V-48-DB-TR














































Reviews:

No comments