background image

Page 4

PAPER

REFER TO LABELED DRAWING ON PAGE 3.

1. Check that the voltage selector switch (4) is set to the required input

voltage,120V or 240V.

For 120V operation the fuse in the mains switch (5) must be a 4A anti-
surge fuse, for 240V operation the fuse must be a 2A anti-surge fuse.

2. Switch on the power, mains switch (5).

3. Set the crease length as follows:-

(i) Line the face of the Speed Stop (2) up with the scale on the copy table

(6) as shown below. (i.e. for a crease length of 100mm, line the face of

the Speed Stop up with the 100mm mark on the copy table).

IMPORTANT.

OPERATING INSTRUCTIONS

4. Slide the sheet under the speed stops and against the side lays in the

direction of the creasing head. As the end speed stop drops down behind
the sheet edge, slide the sheet back to contact the stop. Press the foot
switch to crease the sheet. Repeat this operation for as many stops that
are in use. Slide the sheet out of the machine.

5. The machine is set on the narrow crease at the factory. To change to the

wider crease proceed as follows:-

(i) Undo the inner adjustment knob (7).

(ii) Turn the outer adjustment knob (7) until the spring loaded ball

locates the wider crease position.

(iii) Lightly tighten the inner adjustment knob, place a sheet under the

head and operate the machine. This will centre the tools.

(iv) Tighten the inner adjustment knob securely.

Line this face of the Speed Stop

up with the scale

Summary of Contents for ElectroCreaser 36













Reviews: