14
15
HOW TO USE PRESET WASHING
VARIOUS fUNCTIONS
VARIOUS fUNCTIONS
• The preset time means the washing end time.
• Before using Preset Washing, turn on the water supply and drainage hose to avoid water leakage.
PROCEDURE
1. Press POWER ON/OFF button.
2. Select PROGRAM or FUNCTION as required.
3. Press the PROCESS button until the PRESET light flashes. Press SET button to select the required preset time (washing
end time). PRESET indicate
4. Select water level if necessary.
• Add detergent.
5. Close the washer lid.
6. Press the SRART/PAUSE button.
• After the PRESET has started, the corresponding light will be turned on, and other lights will switch off
approximately one minute later.
• Preset function does not work with DELICATE wash.
• To check the PRESET status, press the SET button, The procedure status will be displayed for 5 seconds.
• To cancel the PRESET, shut off the power.
• To change the PRESET time, press the PRESET button again after cancelling it.
6 7 8 24 0 1 5 (hours)
SHOWER RINSE
It occurs during the last spinning period of washing program. The water is showered onto the clothes to take off foam
and dirt.
WATER SAVER RINSE
It is common rinse. You set the water level for rinse. When the machine runs to rinse program, water flows into the inner
tub to the special level and stops. Then machine will rinse.
OVERFLOW RINSE
It will use more water than the set water level. When the machine runs to rinse program, water flows into the inner tub
to the special level, but do not stops. Water continues flows in and flow out from overflow gap to take off foam and dirt.
• For point 1, if you cancel the shower rinse, it will change to water saver rinse or overflow rinse. It depends on what
you set. For example, under CUSTOM, you cancel the shower rinse, and choose “2” for rinse. There will be 2 times of
water saver rinse; if you choose “2.” for rinse. There will be 2 times of overflow rinse.
How To Set
• Press POWER ON/OFF button to switch on the power, and press the SET button for 4 seconds. To restore it, repeat
above steps or pull out the plug.
MEMORY FUNCTION
When NORMAL, CUSTOM or HEAVY program is selected, 15 seconds after starting, the appliance will memorize this
program and begin to operate under the same program setting when the washer is used next.
• This function is not available for DELICATE/BLANKET program.
• PRESET and WATER LEVEL will not be remembered.
• The SOAK, WASH, RINSE and SPIN for CUSTOM program will be remembered.
WATER LEVEL SETTING
Choose the desired water level during the WASH/RINSE process.
Method:
1. Press FUNCTION button till WASH light flashes
2. Press the WATER LEVEL button to choose the desired water level, press SET button to set wash time.
3. Then press the FUNCTION button again till RINSE light flashes, press WATER LEVEL button again to choose the
appropriate water level.
4. Press SET button to set RINSE time and RINSE type.
5. Press the FUNCTION button till SPIN light flashes, press the SET button to set SPIN time.
6. Press START/PAUSE button to commence washing according to your settings.
TWO STEPS CLEANING FUNCTION
The washer will start washing when water reaches below 2 levels as set. By this, the washer starts working with more
density of detergent.
• This function will not be affected, if water level 1 or 2 is selected, and if DELICATE or BLANKET program is selected.
• When SOAK is selected, this function will not be affected after soaking.
CHILD LOCK FUNCTION
This function avoids accidental opening of the washer by children, etc.
Method of Setting
Press the POWER ON/OFF button to switch on the power, and press the PROGRAM button for 4 seconds until the buzzer
sounds. To restore it, repeat the above steps or pull out the plug.
• The control panel lights will illuminate to indicate E5 if the washer lid is open during operation when CHILD LOCK
function is selected.
CANCELLING THE END BUZZER
If you select this function, the buzzer will not sound at the end of the wash. This is suitable for washing clothes at night.
Method of Cancelling
Press the POWER ON/OFF button to switch on the power, and press the START/PAUSE button for 4 seconds until the
buzzer sounds. To restore it, repeat the above steps or pull out the plug.
HOW TO DRAIN RESIDUAL WATER
• This function will set the drainage valve to expel any residual water inside the washer for a minutes.
• Press the POWER ON/OFF button to switch on the power, and press the FUNCTION button for 4 seconds until the
buzzer sounds. To restore, repeat the above steps or pull out the plug
MAXI SOLVE
Maxo Solve Case has two parts, Detergent Case & Solution Case.
MAXI SOLVE process as follow:
1. Put wash powder into Detergent case.
2. Gentle water current will be injected into the Detergent Case. The detergent
will enter into Solution case evenly and slowly. This process will last around
30 seconds.
3. Strong water current will be poured into the Solution Case to dissolve the
detergent.
4. In this case, the detergent that enters into the tub has been dissolved in the solution case.
Detergent
Case
Solution
Case
MWM-680FA(IM)130312_Layout 1 3/13/12 3:22 PM Page 8
