background image

● This machine should only be repaired by qualified personnel.
● It is forbidden to lubricate, repair and adjust when the machine is running,
● Feet, hands and clothes should be kept at a distance from driven parts.

Periodic inspection and adjustment

● The reliability of the transmission system and adjustment system should be

checked often, you should repair them timely if you find some exceptional
conditions.

● The reliability of protective cover and the fixed bolt of bearing block should be

checked often, you should fasten them when you find them loosen.

● The reliability of the electric system should be checked often to avoid short

circuits.

● The performance of the machine should be checked often, this machine should

be repaired in a timely manner when a failure occurs, running and working with
problems is strictly forbidden.

Nameplate of products

The nameplate of products is the important valid identifying, the place of the nameplate
should be on the front panel. The service people will check the nameplate when you
accept their services, please keep the nameplate clear without losing it.

Inspection before running machine

● When the operator has ensured that there is no non-operator near the mill, this

machine can be operated after making a start signal.

● It is forbidden to run the mill when the protective cover is not closed, the

protective cover is not allowed to be opened or taken away while running the
machine, and the protective cover should be repaired and replaced timely when it
is damaged.

● When the mill is running, you should ensure that there are not any children and

non-operators near the mill.

● You should check and replace the worn-out or broken parts in a timely manner,

and the oil contamination of sediments and impurities should be cleared
promptly.

Understand the Signs

Three sign words stand for the degree of risk: Danger, Warning, Attention

Summary of Contents for JMF Series


















Reviews: