background image

5.4 The operation of machine

a. In order to ensure the raw material can't fall into the crushing cavity at will, you should
close the gap of the feed hopper.
b. Start the motor.
c. Put the raw material into the feeding hopper.
d. Adjust the knob of the adjusting plate slowly, check whether the crush degree can
meet your requirements. You can fix the hand wheel when the crush degree of raw
material can meet your requirement by using the lock nuts.
e. After the end of work, the machine should be run at an idling condition for 1 min to 2
min. The machine should not be stopped until the materials that remain inside the
machine are fully discharged.
f. After the end of the work every day, you should clear away the residue inside the
machine, and keep the body of the machine and the environment around the machine
clear and free of dust.

You should pay attention to the following points when you adjust and operate the

machine:
1) Before running the machine, you should confirm that the motor is grounded
reliably. And you should check all the parts and ensure there are not any unusual
conditions.
2) When you hear an unusual sound during operation, the machine should be shut
down and checked immediately.
3) During operation, you should follow all the safety regulations of the state and local
authorities.
4) Only the brushes and similar products can be used to clean the inner part of the
machine, please don't put your hand into the space between the mill rollers.

You should pay attention to the following points during milling the raw material
1) It is strictly forbidden to take off the outer cover and the protective cover on the
transmission gears between the mill rollers
2) It is strictly forbidden to put your hand into the space between the two mill rollers!

5.5 Notices

a. You must strictly remember that you should put the raw material into the feeding
hopper after starting the machine.

Summary of Contents for JMF Series


















Reviews: