MOPEKA M1017 Quick Start Manual Download Page 15

Federal Communications Commission (FCC) Interference Statement   

 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 

15 of the FCC Rules.   

   

These  limits  are  designed  to  provide  reasonable  protection  against  harmful  interference  in  a  residential 

installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used 

in accordance with the instructions, may cause harmful interference to radio communications.   

 

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does 

cause harmful interference to radio or television reception, which can be determined by turning the equipment 

off and on, the user is encouraged to try to correct the interference by one of the following measures:   

   

 

Reorient or relocate the receiving antenna.   

 

Increase the separation between the equipment and receiver.   

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.   

 

Consult the dealer or an experienced radio/TV technician for help.   

   

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:   

(1)    This device may not cause harmful interference, and (2) this device must accept any interference received, 

including interference that may cause undesired operation. 

 

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could 

void the user’s authority to operate this equipment.   

   

RF exposure warning   

   

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.   

Summary of Contents for M1017
















Reviews: