background image

(Note: Activating WDR at 1080P will reduce maximum frame rate to 15fps.)  

Configure video compression parameters for any of the three available codec instances (Primary H.264, Secondary H.264 and  
MJPEG). Most VMS software solutions will interact with these parameters and thus it is suggested to leave these at default values  
in the web interface. 

VBR aggressiveness however is unique to Moog EXO Cameras and proposes various levels (disabled to aggressive) of motion triggered  
rate control. The more aggressive the setting, the more variation motion will have on the rate control. It is strongly suggested to disable  
VBR aggressiveness for low bit rate scenarios (below 1Mbps) as this parameter may negatively affect perceived video quality.

2.3.3 Configuration / Video In / Video Compression

Frame per sec (fps):

Set Quantization (QP) level to desired rate. The higher the number the greater the compression.  (16 very low, 51 very high)

Frame Rate

-  Allows you to specify the frame rate to be used by the codec.

Rate Control

-

 Allows you to choose between

 Variable Bit Rate

 and 

Constant Bit Rate

. The first option will instruct the H.264  

codec to dynamically adjust the bit rate in order to meet both the target quality (QP) and frame rate settings.  
The second option will instruct the H.264 codec to prioritize target bit rate and vary quality (QP) first and frame  
rate as a last resort.

Min/Max QP

-

This parameter allows you to specify the compression range that the codec will use to determine image quality  
during compression. In order to force a specific quality setting, you can set the minimum and maximum to the  
same value. The lower the value, the better the quality will be.

VBR Aggressiveness

-

 This parameter allows you to specify if the codec should take into account the level of motion in the image for bit 
rate calculations. You can select from 

Conservative

Moderate

 and

 Aggressive 

options for this setting. Using the 

Conservative

 option, the codec will allow bit rate to drop up to ¾ of the configured target bit rate when no motion 

is detected in the image. Using the 

Moderate

 option, the codec will allow bit rate to drop up to ½ of the configured 

target bit rate when no motion is detected in the image. Using the 

Aggresive

 option, the codec will allow bit rate to 

drop up to ¼ of the configured target bit rate when no motion is detected in the image. You can disable this feature 
by selecting the 

disabled

 option.

Summary of Contents for EXPD7C1-2








































Reviews: