The last parameter is the mode and T for toggle is
necessary, this will toggle between 0 (off) and the value
you select, in other words, switch the function On and
Off.
Event #0F, #10 - Midi Sustain Aux 2, 3
These events are used to Send a third and fourth sustain
message along with the Foot Pedal if it is assigned to
Controller #64. They are identical to the
Midi Sustain
Aux 1
described above, except the Function number
parameter following the word Function will be #02 and
#03 respectively. The parameters are Function channel,
Event Type, Function # (0F or 10 in these cases), Midi
channel and Mode.
If you assign 3 buttons to Events #0E thru #10, you can
switch on/off the sending of Sustain to 3 extra devices
on individual midi channels, from one button.
Event #11 to #4F - Play a Four note Chord.
These events are used to play a four note chord,
according to the Chord Library Chart. The parameters
are Function channel, Chord # (any number from 11 to
4F), Chord Velocity and Mode.
Move the cursor to the first parameter and
make sure it
is Function channel 1
. Move the cursor to the Second
parameter and change it to Function, move the cursor to
the parameter after the Function name and edit it to be
the number of the chord you want assigned to the
key/button as shown on the Chord Library Chart.
Move the cursor to the next parameter and choose the
velocity for the chord (1 = minimum, 7F = maximum).
If you leave this as 0 nothing will happen.
NOTE
: the number is in Hexadecimal, 40 = 64, 7F =
max, 01 = min.
The last parameter is the mode and ^ for On/Off is
necessary, this will play as a keyboard should (on when
pressed, off when released).
When you play the chords, the HOLD function will hold
the chord, and the Transpose Function will alter the
pitch of the whole chord.
You will also find that you can also play/add single
notes as well as the chord, if you have keys assigned to
Note On.
Make sure all these Function functions are on
Function channel 1, the other Function channels are
reserved for future use.
-----------------------------------------------------
EDIT CONTROLLER NAME
Press the MENU button to enter the EDIT CONT.
NAME section.
In this menu page the names and number formats can be
edited for every Controller.
Select the Controller by moving it, then use the
CURSOR button to select the parameter and the
DOWN/UP buttons to change the value.
When the cursor is on the name fields, the up/down
buttons will change the character, pressing the cursor
button again will advance to the next character.
When the cursor is on the last parameter to the UP of
the LCD screen you can change the numbering display
format for the controller. Use the Down/Up buttons to
change the mode and move the desired controller to see
the display you will get.
For example you may not want the normal 0-127
numbers and would prefer -64 to +64 with 0 as center,
to better display Dry/Wet reverb mix or Pitch-bend.
There are these options;
Override (just show “Controller #??” and numbers in
decimal)
Hexadecimal 00 to 7F
Hexadecimal Centered -40 to +3F
Decimal 0 to 127
Decimal Centered -64 to +63
Hexadecimal with Indicator 00-7F
Hexadecimal Centered with Indicator -40 - +3F
Decimal with Indicator 0-127
Decimal 64 Centered with Indicator -64 - +63
-----------------------------------------------------------
COPY MEMORY
Press the MENU button to enter the COPY MEMORY
section.
In this menu the current memory can be copied to
another memory. If the current memory is not the one
you want to copy, go to the MEMORY SELECT section
to select the current memory, then return to this section.
The target memory can be selected with the DOWN/UP
buttons.
Hold the STORE button for 2 seconds to start the copy
procedure.
----------------------------------------------------------
