background image

Limited Warranty for Moog Videolarm Products 

Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:

PRODUCT CATEGORY

PARTS   \   LABOR

All Enclosures and Electronics*

Five     (5) Years

Poles/PolEvators

/CamEvator

Three  (3) Years

Warrior Series™/Q-View™/IR Illuminators

Five     (5) Years

SView Series™

Five     (5) Years  **6 months if used in auto scan/tour operation

Controllers

Five     (5) Years

Power Supplies

Five     (5) Years

EcoKit

Three  (3) Years

Accessory Brackets

Five     (5) Years

Liberty Dome

Three  (3) Years

*DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™

Three  (3) Years  **6 months if used in auto scan/tour operation

During  the  labor  warranty  period,  to  repair  the  Product,  Purchaser  will  either  return  the  defective  product,  freight  prepaid,  or  deliver  it  to  Moog  Videolarm 
Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with 
a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip.  To obtain a RMA# you must contact our Technical Support 
Team  at  800.554.1124,  extension  101.  Moog  Videolarm  will  return  the  repaired  Product  freight  prepaid  to  Purchaser.  Moog  Videolarm  is  not  obligated  to 
provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or 
parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions.

TERMS AND CONDITIONS

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE:

  If  Purchaser  believes  that  the  Product  is  defective  in  material  or  workmanship,  then  written  notice  with  an 

explanation of the claim shall be given promptly by Purchaser to Moog Videolarm.  All claims for warranty service must be made within the warranty period. 
If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of 
investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period 
of the entire Product. The specifi c warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that 
part or the remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE:

 Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any 

Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.  

3. EXCEPTIONS TO LIMITED WARRANTY:

 

Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the 

warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes, 
earthquakes), modifi cation, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance 
procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the 
Product.  Furthermore, Moog Videolarm shall have no liability where a schedule is specifi ed for regular replacement or maintenance or cleaning of certain parts 
(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-qualifi ed personnel; operation of the Product outside of the 
published environmental and electrical parameters, or if such Product’s original identifi cation (trademark, serial number) markings have been defaced, altered, 
or removed.  Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not 
been sold by Moog Videolarm to the Purchaser.  All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS” 
(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product.  Any 
cost associated with removal of defective product and installation of replacement product is not included in this warranty.

4. PROOF OF PURCHASE:

 

The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, 
INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR 
ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL 
CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT 
THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS 
PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.

LIMITATION OF LIABILITY

THE  LIABILITY  OF  Moog  Videolarm,  IF  ANY,  AND  PURCHASER’S  SOLE  AND  EXCLUSIVE  REMEDY  FOR  DAMAGES  FOR  ANY  CLAIM  OF  ANY  KIND 
WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL 
PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER 
FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, 
REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

Summary of Contents for VLC485













Reviews: