background image

Installation

Page 3

XG0675 - 151207

WARNING

This remote control system must be installed exactly as outlined in these instructions. Read all instructions 

completely before attempting installation. Follow instructions carefully during installation. Any modifications of this 

remote control or any of its components will void the warranty and may pose a fire hazard.

Wiring Instructions

A qualified electrician should install the remote control 

system

1. 

Disconnect and remove the wall switch wire from 

terminals 3 and 4 of the control box. See 

Figure 3

 or 

Figure 3a

.

2. 

Feed the red wires from the remote receiver through 

the control box side. See 

Figure 5

.

3.  Connect the Red wires to Terminals 3 and 4 of the 

control box. See 

Figure 3

 or 

Figure 3a

. When con

-

necting two connectors together on a single pole, 

place connectors back-to-back. See 

Figure 4

.

4.  Plug the power cord from the receiver into the 110VA 

plug on the side of the control box. See 

Figure 5

.

5. 

Attach the receiver to the control box cover or to the 

wall using the velcro strips attached. See 

Figure 6

.

3 4

Connection 

110 VAC

Red Wires 

From Receiver

3 4

Figure 3. 

Connection to Control Box 

Figure 3a. 

Connection to Control Box  

(RP424PFC)

Figure 5. 

Plug to receptacle

Figure 6. 

Installing Receiver

Figure 4. 

Place connectors back-to-back when installing

Summary of Contents for RXM5010









Reviews: