background image

Figure 8.

  Factory installed Top Vent Pressure Sensing Tube

Figure 8a.

  Supplied Rear Vent Pressure Sensing Tube

Figure 9.

  Removal of Top Vent air baffle and pressure sensing tube.

Figure 9a.

  Removal of Top Vent air baffle and pressure sensing tube.

NOTE:

    Rear  vent  pressure  sensing  tube  is  shipped  inside  the 

control box.

R520 Power Vent Indoor Gas Fireplace

Page 14

XG0771 - 150204

Installation

Section 3-1-2: Converting the Pressure Sensing 

Tube and Air Baffle 

When the 

R520*

 is converted from Top Vent to Rear Vent, the 

pressure sensing tube must be removed and replaced with 

supplied Rear Vent pressure sensing tube and air baffle must be 

relocated as described below. 

1. Remove two screws from the air baffle installed over the Top 

    

    Vent from inside the firebox. Once air baffle is removed, replace  

    the two screws back into the same position. 

Note: 

Not all models are equipped with an air baffle. Only convert 

if available. 
2. Remove Top Vent pressure sensing tube by loosening the    

..   

    compression nut with a 1/2" wrench. 

3. Position the supplied Rear Vent pressure sensing tube as

4. Install air baffle over Rear Vent from inside the firebox with two  

    screws provided at the Rear Vent. 

shown in

 Figure 9a

. Hand tighten the compression nut by 

hand and then a half-turn with a wrench. 

Do not over tighten.

 

Summary of Contents for R520











































Reviews: