manualshive.com logo in svg

Montigo PL38DF, Installation & Maintenance Manual

Share
Download
Montigo PL38DF Installation & Maintenance Manual Download Page 15

Page 15

PL38DF* Indoor Gas Fireplace

XG0216 -160215.1

Installation

Figure 14. 

Corner (Rigid) installation. (NG Models Only)

Figure 14a. 

Corner (Flex) installation. (NG Models Only)

45° Corner Installation.

Attach an PEL-45 (45° elbow) directly onto the flue collar. Cut the 

PXT-20 to suit, and attach it to the PEL-45. Slide the fireplace into 

position and attach to the termination. 

  45° or less Corner Installation.
  Use a PTO-4 termination and an PFL-1 or PFL-2 (12" or 24" 

compressed length) and a frame, if appropriate. Flex may be 

turned to obtain desired degree of angle required but must not 

exceed 45°.

  Note: Through the wall venting kits are also available for both 

the Straight and the Corner Installation. The Kit includes a heat 

shield, a PFL-18 (f/f) flexible pipe, and a termination with or 

without a mounting frame.

PEL-45 Elbow

PEL-90 Elbow

PXT-18

IMPORTANT:

Corner Installation is available for 

PL38DF Top Vent Units Only. Ensure 

minimum Vertical Venting Height of 40" 

is maintained in corner installations.

Note:  Images are shown without screens for clarity purposes. 

However, your fireplace should not be operated without proper 

installation of screens.

Summary of Contents for PL38DF











































Reviews:

No comments

Brands by name

Popular brands

Load more brands