background image

Page

XG0305

MD34-BV Homefire

Introduction

About this fireplace:

Thank you for choosing a Montigo Gas Fireplace. The 

MD34-BV

 fea-

tures a dual burner with glowing embers and a realistic fibre logset. 
TheMD34 is available in two versions:

  MD34-BV

 --

 

Standard (Continuous) Pilot

 

MD34-BV-I

 --

 

Intermittent (Electronic) Pilot

The MD34-BV is certified in Canada and the USA  as a 

Vented Gas 

Fireplace Heater

 (ANSI Z21.88-2000· CSA 2.33-2000) and is rated for:

 

Natural Gas

   21,500 BTU/H (6.30  Kilowatts) Input

 

 

 

15,050 BTU/H (5.13 Kilowatts) Output

 

Propane

 

21,500 BTU/H (6.30 Kilowatts) Input

 

 

 

15,050 BTU/H (4.41 Kilowatts) Output

How to use this manual:

This manual covers all models and unless otherwise specified, the 
designation MD34-BV refers to all models. Sections which are spe-
cific to a particular model are marked with a                            
    symbol, plus the appropriate model number.

Warranty and Installation Information:

The Montigo warranty will be voided by, and Montigo

 

disclaims any 

responsibility for, the following actions:

 

Modification of the fireplace and/or components including Direct-
Vent assembly or glass doors.

 

Use of any component part not manufactured or approved by 
Montigo in combination with this Montigo fireplace system.

 

Installation other than as instructed in this manual.

Consult your local Gas Inspection Branch on installation require-
ments for factory-built gas fireplaces. Installation & repairs should be 
done by a qualified contractor.

Installations in Canada

 must conform to the current 

CAN/CGA 

B-149.1

 and 

.2

 Gas Installation Code and local regulations. If the 

optional air-circulating fan kit is installed, it must be electrically 
grounded in accordance with 

CSA C22.1

 Canadian Electrical Code 

Part 1 and/or Local Codes.

Installations in the USA

 must conform to local codes, or in the 

absense of local codes to the National Fuel Gas Code, 

ANSI 

Z223.1-1988

. If the optional air-circulating fan is installed, it must be 

grounded in accordance with local codes or, in the absence of local 
codes, with the National Electrical Code, 

ANSI/NFPA 70-1987.

Table Of Contents

Introduction

 ............................................................................... 2

Installation

 

Installing the Fireplace Shell .......................................... 3

 

Installing the Gasline ...................................................... 4

 

The Remote Switch ........................................................ 4

 

B-Vent Installation .......................................................... 4

 

Construction around the fireplace

 

 

Facing ................................................................ 5

 

 

Mantels and Surrounds ..................................... 5

 

Wiring   ......................................................................5 - 6

 

Installing the Logset ....................................................... 6

 

Removing and Installing the Insert ................................. 7

 

Removing and Installing the Door .................................. 7

Operation

 ............................................................................8 - 10

Maintenance

 ..................................................................... 10 - 11

Warranty

 .................................................................................. 12

Appendix

 

A. Spare Parts .............................................................. 13 

CAUTIONS

Due  to  its  high  operating  temperatures,  the  appliance 
should  be located out of traffic & away from furniture and 
draperies.

  Children and adults should be alerted to the hazards 

of the high surface temperature, which could cause 
burns or clothing ignition.

  Young children should be carefully supervised when 

they are in the same room as the appliance.

  Clothing or other flammable materials should not be 

placed on or near the appliance.

Summary of Contents for MD34-BV Homefire Plus















Reviews: