background image

Installation

Operation &

Maintenance

What To Do If  You Smell Gas:

•   Do not try to light any appliance.

•   Do not touch any electrical switch;  do not use any phone in 

your building.

•   Immediately call your gas supplier from a neighbor's phone.  

Follow the gas supplier's instructions.

  For Your Safety:

 

Do not store or use gaso

-

line or other flammable 

vapors and liquids in 

the vicinity of this or any 

other appliance.

See-Thru

Gas Fireplace

M40DV-ST

M40DV-ST 

(MH)

 

Installer:

 

Leave this manual 

with the appliance.

  Consumer: Leave this man-

ual for future reference.

Check local codes and read all 

instructions prior to installation.

®

C

US

                 WARNING!

 

Improper installation, adjustment, 

alteration, service or maintenance 

can  cause  injury  or  property 

damage. Refer to this manual. For 

assistance

 

or additional information

 

consult a qualified

 

installer, service 

agency or the  gas supplier.

Safety Notice:

Glass  doors  on  gas  fireplaces  are 
extremely hot while the fireplaces is on 
and remain hot even after the fireplace 
has  been  turned  off.    Safety  screens 
are available and can reduce the risks 
of severe burns.  Please keep children 
away from the fireplace at all times.

Summary of Contents for M40DV-ST



























Reviews: