background image

INTRODUCTION 

Thank you for purchasing this Z-Wave Plus® 700 Series Door/Window 
Sensor from Monoprice

! This sensor is a wireless Z-Wave® enabled 

device and is fully compatible with any Z-Wave enabled network.  
Z-Wave is an interoperable, two-way RF mesh networking technology 
used for home automation and security. Every AC powered Z-Wave 
device acts as a signal repeater, so multiple devices result in more 
possible transmission routes, which helps eliminate RF "dead spots" in 
the network. Any Z-Wave enabled device displaying the Z-Wave logo 
can be used with Z-Wave devices from other manufacturers. 
This sensor mounts to a door or window, detects when it is opened or 
closed, and sends a Z-Wave trigger signal to the network. These trigger 
signals can be used to activate various other devices and perform 
preprogrammed tasks. When the sensor is included into a secured  
Z-Wave network, all communications will be encrypted. This device 
supports the Security S0, Security S2 Unauthenticated, and Security S2 
Authenticated protocols. 
 

CUSTOMER SERVICE 

The Monoprice Customer Service department is dedicated to ensuring 
that your ordering, purchasing, and delivery experience is second to 
none. If you have any problem with your order, please give us an 
opportunity to make it right. You can contact a Monoprice Customer 
Service representative through the Live Chat link on our website 
www.monoprice.com or via email at [email protected]. Check 
the website for support times and links.

 

 

Summary of Contents for Z-Wave 700 Series















Reviews: