Monoprice 44091 User Manual Download

Page: 33 / 37

SPECIFICATIONS

P/N

44091

Number of Extruders

Positioning Accuracy

X/Y Axis: 0.011mm, Z Axis: 0.0025mm

Layer Resolution

100 ~ 400 microns

Build Volume

220 x 200 x 250 mm

Nozzle Diameter

0.4mm (default), 0.6/0.3 mm (optional)

Build Speed

10 ~ 150 mm/sec

Maximum Extruder Temperature

240°C (default) or 265°C (optional),
depending on extruder

Supported Filament Types

ABS, PLA, PC, PETG, PLA-CF, ASA, PETG-CF

Supported Software

MP FlashPrint

FlashPrint Input File Types

3MF, STL, OBJ, FPP, BMP, PNG, JPG, JPEG

FlashPrint Output File Types

GX, G

Connectivity

USB Flash Drive, Wi-Fi®, Ethernet

RF Operating Frequency

2400 ~ 2497 MHz

Maximum RF Power

7 ±1 dBm

USB Flash Drive File System

FAT32

Input Power

100 ~ 240 VAC, 50/60 Hz, 13.3A

Maximum Power Consumption

320 watts

Fuse Type

T10AL250V (5 x 20 mm)

Operating Temperature

+59 ~ +86°F (+15 ~ +30°C)

Operating Humidity

20 ~ 70% RH, noncondensing

Dimensions (LxWxH)

19.7" x 18.5" x 21.3" (500 x 470 x 540 mm)

Weight

60.0 lbs. (27.2 kg)

Summary of Contents for 44091






































Search results

Summary of Contents for 44091

Reviews:

Related manuals for 44091

Brands by name

Popular brands

Monoprice 44091, User Manual

Search results

Summary of Contents for 44091

Reviews:

Related manuals for 44091

Brands by name

Popular brands