Monoprice 44091 User Manual Download | Manualshive

Page: 11 / 37

background image

11

GETTING STARTED

1.

If you have not already installed the FlashPrint software package, install it now by
following the instructions in the

SOFTWARE INSTALLATION section above.

2.

Ensure that the Power Switch on the printer is in the OFF (O) position.

3.

Plug one end of the included AC Power Cord into the Power Connector on the
printer, then plug the other end into a nearby AC power outlet.

4.

Flip the Power Switch on the printer to the ON (I) position.

«
...
9
10
11
12
13
...
»

Summary of Contents for 44091






































Reviews:

No comments

Related manuals for 44091

Brand: Oki Pages: 33

Brand: Oki Pages: 11

Brand: OKIDATA Pages: 58

Brand: QMS Pages: 122

Brand: QMS Pages: 306

Brand: Xerox Pages: 73

Brand: Xerox Pages: 2

Brand: Unitech Pages: 2

Brand: QMS Pages: 27

Brand: QMS Pages: 3

Brand: Ricoh Pages: 406

Brand: Felix printers Pages: 26

DocuPrint C2535 A

Brand: Xerox Pages: 120

Brand: Gainscha Pages: 12

Brand: Oki Pages: 2

VersaUV LEJ-640

Brand: Roland Pages: 321

Brand: Go Pages: 3

Nuvera 100 roduction Systems

Brand: Xerox Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands