Monogram ZWL1126SR Installation Instructions Manual Download Page 5

31-7000165   Rev.1

5

Installation Instructions

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of 

an electrical short circuit, grounding reduces the risk 

of electric shock by providing an escape wire for 

the electric current. This appliance is equipped with 

a cord having a grounding wire with a grounding 

plug. The plug must be plugged into an outlet that is 

properly installed and grounded. Consult a qualified 

electrician or serviceman if the grounding instructions 

are not completely understood, or if doubt exists as to 

whether the appliance is properly grounded.

WARNING

 

Improper use of the grounding plug can result in a risk 

of electric shock. 

Do not use an extension cord. If the power supply 

cord is too short, have a qualified electrician or 

serviceman install an outlet near the appliance.

3-prong plug

Grounding pin

3-prong receptacle

Grounded receptacle box

Permanent and 

Correct Installation

DRAWER INSTALLATION

1.  Place the drawer adjacent to the wall or cabinet 

opening. Plug the power supply cord into the 

electrical outlet. 

2.  Loop (do not tie) a 36” (91 cm) string around the 

power supply cord before the drawer is slid into 

place. This will keep the cord from falling behind the 

drawer.

3.  Lift drawer into cabinet cutout using the opening as 

a grip. Carefully guide the drawer into the prepared 

opening. 

4.  As you slide the drawer back, pull the string so that 

the cord will lie on top of the drawer in a natural loop 

and avoid pinching the cord between the drawer and 

the wall.

5.  When you are sure the cord is out of the way, slide 

the drawer ¾ way back into the opening. Remove the 

string by pulling on one end of the loop.

6.  Slide the drawer all the way until the mounting flange 

is flush with the face of the cabinet. See Figure 5.

7.  Open the drawer. Using the 4 holes on the mounting 

flanges as a template, drill pilot holes the cabinet 

using a 

1/16

” drill bit. See Figure 5.

8.  Secure the drawer with the 4 screws supplied. It is 

recommended that the screws be hand tightened.

Mounting 

Flange

Figure 5

Parts Supplied

4 Screws

Summary of Contents for ZWL1126SR





















Reviews: