background image

19

STEP 17  INSTALL TOEKICK

• Locate the supplied toekick (shipped taped to 

the side of the refrigerator). Install with the 2 screws
provided. Adjust to the desired height and tighten 
the screws.

• A custom toekick can be installed to match 

or complement the surrounding cabinetry. 
Use the supplied toekick as a template 
to cut the shape.

STEP 15  CONNECT POWER, CLOSE

GRILLE PANEL

• Open the grill panel.
• Plug in the power cord (if necessary) by reaching 

into the opening next to the water filter. If access is 
too tight, remove the 2 screws holding the water
filter bracket and move aside. Plug in the power cord
and secure the bracket with the original screws.

• Check to make sure power to refrigerator is on 

by opening refrigerator door to see if interior lights
are on.

• The temperature controls are preset at 3°C for 

the fresh food section and -18°C for the freezer.

• Allow 24 hours to stabilize before making 

adjustments.

Supplied Toekick

1/4" or Thicker Toekick

INSPECT FINAL INSTALLATION

Check door alignment
Stand back away from the refrigerator to inspect 
the final installation.
• Check to be sure the handles are evenly aligned with

each other at the top. To adjust, loosen the handle
screws and slide up or down. Tighten the screws.

• Shipping or the addition of heavy door panels 

may have caused the doors to move slightly out 
of alignment. 

• If necessary, the fresh food door may be adjusted up

or down to align with the freezer door.

• Use a 5/16" wrench to adjust the hinge pin as shown.

Bushing

Door Hinge

Case Hinge

5/16" Wrench

Raise

Door Out of

Alignment

Master Light

Switches

Electrical

Outlet Access

Bracket

Screws

Installation Instructions

Power Switch

Green Power Light

Feeler Arm

STEP 16  START ICEMAKER

• Flip the switch to I (ON). The icemaker will begin

operation automatically.

• Be sure nothing interferes with the sweep of the 

feeler arm. 

• Discard the first full bucket of ice cubes.
• To turn the icemaker off, set the switch to O (OFF)

.

6 mm or Thicker Toekick

Supplied Toekick

Summary of Contents for ZIS420N

























Reviews: