manualshive.com logo in svg

Monogram ZIS360N, Design Manual With Installation Instructions, Page: 18 / 20

Share
Download
Monogram ZIS360N Design Manual With Installation Instructions Download Page 18

STEP 14  INSTALL TOEKICK

• Locate the supplied toekick (shipped taped to

the side of the refrigerator). Install with 2 screws
provided, adjust to desired height and tighten screws.

• A custom toekick can be installed to match or

complement the surrounding cabinetry. Use the
supplied toekick as a template to cut the shape.

STEP 13  START ICEMAKER

• Flip the switch to I (ON). The icemaker will begin

operation automatically.

• Be sure nothing interferes with the sweep of the

feeler arm.

• Discard the first full bucket of ice cubes.
• To turn the icemaker off, set the switch to O (OFF).

STEP 12  CONNECT POWER

• Connect refrigerator power cord plug to a properly

grounded receptacle, accessible through the top of
the grille opening.

• Check to make sure power to refrigerator is on by

opening refrigerator door to see if interior lights
are on.

• The temperature controls are preset at 37

°

F for the

fresh food section and 0

°

F for the freezer.

• Allow 24 hours to stabilize before making

adjustments.

Power Switch

Green Power Light

Feeler Arm

Installation Instructions

18

Supplied Toekick

1/4" or Thicker Toekick

INSPECT FINAL INSTALLATION

Check door alignment
Stand back away from the refrigerator to inspect the
final installation.
• Check to be sure handles are evenly aligned with

each other at the top. To adjust, loosen handle
screws and slide up or down. Tighten screws.

• During shipping or the addition of heavy door

panels may have caused the doors to move slightly
out of alignment.

• If necessary, the fresh food door may be adjusted

up or down to align with the freezer door.

• Use a 5/16" wrench to adjust the hinge pin as

shown.

Bushing

Door Hinge

Case Hinge

5/16" Wrench

Raise

Door Out of

Alignment

Raise
Grille
Panel

Master Light

Switch

Electrical

Outlet

Summary of Contents for ZIS360N





















Reviews:

No comments