background image

Installation Instructions - Stainless Steel Installation

48

Move Unit into Final Position

• Move appliance toward its final installed location. 

Align the tabs on the wall bracket with the openings 
in the back of the unit. 

• The unit has “L” bolts in the upper left and right cor-

ners inside of the access compartment. These bolts 
will interlock with the wall bracket and secure the 
unit using the washers and hair pin cotters in the 
hardware kit once the unit has been leveled and is 
in the final position. 

 STEP 4    INSTALL ANTI-TIP 

BRACKET (cont.)

 STEP 5  LEVEL UNIT

All models have 4-point leveling. The front is support-
ed by leveling legs; the rear is supported by adjustable 
wheels. Both are accessible from the front of the unit.

• To level the back of the unit, turn the 7/16” hex nut 

located above the front wheels. Turn clockwise to 
raise or counterclockwise to lower the unit.

• For front leveling, use a 1-1/4” open-end wrench.

• Adjust height of unit to match installation cutout 

opening 84-1/2”. The unit should be level and plumb 
with cabinetry.

CAUTION

 

The rear leveling wheels and front leveling legs are 
limited to a maximum height adjustment of 1”. If the 
installation requires more than 84-1/2” height, the 
installer should elevate the unit on a sheet of plywood 
or runners. Cabinetry trim could also be added across 
the top of the opening to shorten the opening. If 
you attempt to raise the unit more than 1”, you will 
damage the front leveling legs and the rear leveling 
wheels.

ATTENTION

Les roues de nivellement arrière et les pattes de 
nivellement avant permettent un réglage maximal 
de 25 mm (1 po). Si l’ouverture pour l’appareil 
ménager a une hauteur supérieure à 2,15 m (84-1/2 
po), l’installateur doit élever l’appareil ménager sur 
une feuille de contre-plaqué ou des glissières. Il est 
également possible d’ajouter des baguettes de finition 
des placards sur le haut de l’ouverture afin de la 
réduire. Lever l’appareil ménager de plus de 25 mm  
(1 po) endommage les pattes de nivellement avant et 
les roues de nivellement arrière.

Summary of Contents for ZIRP360NHLH





















































Reviews: