Mono FG166-G11LH Setup And Operation Download

Page: 35 / 70

MX Eco-touch Rotary Rack Gas Oven (FG166)

Rev. B21 21-05-21

MONO EQUIPMENT

IF THE OVEN IS NOT UP TO

TEMPERATURE IT WILL SHOW THE

HEATING SCREEN.

WAIT FOR THE OVEN TO REACH

TEMPERATURE

WHEN THE OVEN IS AT THE

CORRECT TEMPERATURE, THE

“READY”

SCREEN WILL SHOW.

1. OPEN DOOR AND LOAD PRODUCT.
2. CLOSE THE DOOR FULLY.
3. TOUCH

“START”

TIP

TO HELP TO KEEP THE OVEN HOT,

TRY NOT TO KEEP THE DOOR OPEN

MORE THAN NEEDED

THIS SCREEN WILL SHOW WHILE

THE PRODUCT IS BAKING

SET TEMPERATURE

TEMPERATURE PROFILE BAR

BAKE TIME PROGRESS BAR

ACTUAL OVEN

TEMPERATURE

BAKE PHASE

(WHEN USED)

HEATING SCREEN

READY SCREEN

IF THE OVEN IS TOO HOT FOR THE TEMPERATURE
CHOSEN, THE SCREEN WILL TELL YOU TO OPEN THE
DOOR TO AID COOLING.

View

NOTE
The actual temperature shown will rise and fall
above and below the set temperature as the
oven cools and reheats. This is not a fault

BAKE TIME LEFT

Summary of Contents for FG166-G11LH







































































Search results

Summary of Contents for FG166-G11LH

Reviews:

Related manuals for FG166-G11LH

Brands by name

Popular brands

Mono FG166-G11LH, Setup And Operation

Search results

Summary of Contents for FG166-G11LH

Reviews:

Related manuals for FG166-G11LH

Brands by name

Popular brands