manualshive.com logo in svg

Mono FG166-G11LH, Setup And Operation, Page: 25 / 70

Share
Download
Mono FG166-G11LH Setup And Operation Download Page 25

MX Eco-touch Rotary Rack Gas Oven (FG166) 

Rev. B21 21-05-21 

MONO EQUIPMENT 

25

 

8.0 GENERAL MAINTENANCE 

 

To maintain the warranty conditions, the oven must undergo service at specific intervals. Below 
is the service program with the given intervals: 

 

Maintenance every 3 months 

 

Lubrication: 

Door lock – use heat-resistant grease 

 

Maintenance every 

12 months 

 

Check/adjust: 

Door lock mechanism 
Internal door release mechanism 
Lighting, including cables 
Damper function 
Drive belt tension 
Limit positions 
Water connection tightness 
Solenoid valve operation 
Rack hanger bearing 
Function check 
Chamber temperature calibration 

 

Gas heated oven 

Servicing of the gas burner, heat exchanger, and flue should be carried out at least once every 
12 months by a suitably qualified person. 

 

Lighting 

If the lighting in the door fails to operate, contact the Mono Service Department. 
It cannot be replaced by the user.

Summary of Contents for FG166-G11LH







































































Reviews:

No comments