Monnit ALTA Wireless
Carbon Monoxide Sensor User Manual Download Page 19

SAFETY RECOMMENDATIONS
READ CAREFULLY

Be sure the use of this product is allowed in the country and in the environment required. 

The use of this product may be dangerous and has to be avoided in the following areas:

•  Where it can interfere with other electronic devices in environments such as hospitals 

airports, aircrafts, etc. 

• 

Where there is risk of explosion such as gasoline stations, oil refineries, etc.

It is responsibility of the user to enforce the country regulation and the specific environment 

regulation. 

 

Do not disassemble the product; any mark of tampering will compromise the warranty 

validity. We recommend following the instructions of this user guide for correct setup and 

use of the product.

Please handle the product with care, avoiding any dropping and contact with the internal 

circuit board as electrostatic discharges may damage the product itself. The same precau-

tions should be taken if manually inserting a SIM card, checking carefully the instruction for 

its use. Do not insert or remove the SIM when the product is in power saving mode. 

 

Every device has to be equipped with a proper antenna with specific characteristics. The 

antenna has to be installed with care in order to avoid any interference with other electronic 

devices and has to guarantee a minimum distance from the body (23 cm). In case this re-

quirement cannot be satisfied, the system integrator has to assess the final product against 

the SAR regulation. 

 

The European Community provides some Directives for the electronic equipments intro-

duced on the market. All the relevant information’s is available on the European Community 

website: http://ec.europa.eu/enterprise/sectors/rtte/documents/ 

Additional Information and Support

For additional information or more detailed instructions on how to use your Monnit Wireless 

Sensors or the iMonnit Online System, please visit us on the web at 

monnit.com/support

.

Monnit, Monnit Logo and all other trademarks are property of Monnit, Corp.  
© 2020 Monnit Corp. All Rights Reserved.

 

Monnit Corporation

3400 South West Temple

Salt Lake City, UT 84115

801-561-5555

www.monnit.com

AUG-016 (02/20)

Summary of Contents for ALTA Wireless Carbon Monoxide Sensor




















Reviews: