background image

B U L L E T I N

764A

I N S T A L L A T I O N   &   O P E R A T I O N

D u s t

A l a r m

®

E S

Thank  you  for  purchasing  a  quality  product  manufactured  by  Monitor

Technologies  LLC.  We  realize  that  you  do  have  a  choice  of  vendors

when procuring broken bag detectors and we sincerely appreciate your

business!
This manual contains the information necessary to ensure a safe and

successful installation. Please read and comply with the section on the

back of this manual pertaining to SAFETY. Doing so will ensure proper

operation of the equipment and the safety of all personnel.
Before discarding shipping container, please inspect it thoroughly and

verify that all parts ordered are accounted for.  Sometimes smaller parts

become stuck under carton flaps and other packaging materials.
In  the  event  that  information  contained  herein  does  not  completely

satisfy your requirements or answer your questions, you may contact

Technical  Support  on  our  at  website  www.monitortech.com,

by  telephone  at  1-800-766-6486  (1-630-365-9403),  or  by  e-mail  at 

[email protected].  If  your 

Dust

Alarm

®

ES

ever  requires

service either in or out of warranty, please contact us and obtain an RMA

number prior to shipping the unit to us. 

Dust

Alarm

®

ES 

Broken Bag Detector

®

www.monitortech.com

Summary of Contents for DustAlarm ES









Reviews: