Moni HZBB-1177, Instruction Manual

Page: 14 / 16

•Care should be taken in unpacking and assembly of the vehicle. Do not allow the children to play with any of the parts or to
help in the assembly of the vehicle. Risk of injury due to small parts, sharp edges and sharp points in the
vehicle’s
unassembled state.
• Identify all parts before assembly and save all packing material until assembly is complete to ensure that no parts are
discarded
• After each step you must check if each part is correctly placed and well fixed. Follow strictly each step and study well the
assembly figures.
• Assembly tools needed: screwdriver (not included in the set) and spanner (not included in the package).
•
DO NOT over-tighten in order to avoid any damage.
•If you find problems with assembly, contact the store from where you purchased the product.
1.Step A - Installing the front fender and front fork - See Figures 1, 2 and 3: Thread the front fork through the fender
opening. The mudguard must fit into the fork. Thread the plastic decorative part through the bottom part of the front fork. Fix
it using a screw and a screwdriver.
2.Step B
– Installing the front wheel - See Figure 4, 5 and 6:
Take the front wheel and place it in the middle of the front
fork. Slide the front axle through the caps and the front wheel. Then insert the washer and tighten it with a nut and a wrench.
3.Step C
– Installing the windshield and the mask - See Figures 7, 8, 9, 10, 11 and 12
: Take the steering fork with the
front wheel and insert it through the hole of the body of the motorbike. Attach the cables coming out of the mask to those
coming from the motorbike`s body. Put the cables inside the opening in the body. Take the mask and attach it to the body of
the motorbike. Be careful not to damage the cables! You will hear a clicking sound when the mask is fixed. Attach the
rearview mirrors to the head mas. Secure them with screws and screwdriver.
4.Step D - Installing the handlebar - See Figures 13 and 14: Connect the cables of the handlebar to those of the
motorbike. Attach the handlebar to the tip of the steering fork. Secure it using the cap.
5.Step E:
A. Installing the rear wheel and the auxiliary wheels for model Sport
– See Figures 15, 16, 17, 18 and 19:
Attach the
rear tire to the back part of the motorbike body. The black cogwheel of the rear tire must be attached to the white cogwheel
of the gear box. place a bushing on the other side of the wheel. Slide the rear axle through the openings in the body and the
rear wheel. Put a washer and a nut on both sides of the rear axle. Fix with a wrench. Install the auxiliary wheels to the
bottom of the motorbike body using screws and a screwdriver.
B. Attaching the rear wheels of model Legend
– See Figures RW1, RW2, RW3, RW4 и RW5:
Slide the rear axle through
the openings of the gearboxes in the rear motorbike body. Place a rear wheel on each side of the axle. The black cogwheels
of the rear tires must fit to the white cogwheel of the rear gearboxes. Adjust the axle so that it comes on equal parts on both
sides of the motorbike. Attach a gasket and a nut on each side of the axle. Fix the nuts using wrenches. While fixing one of
the nuts, hold the other one using a wrench. Finally attach the caps.
6.Step F - Installing the foot pedal - See Figures 20 and 21: Connect the power cord to the foot pedal. Insert the cables in
the opening in the motorbike body. Insert the footrest with the foot pedal in the
motorbike’ body and press carefully until you
hear a clicking sound. Attach the other footrest on the left side of the motorbike.
7. Step G
– Connect the battery – See Figures 22 and 23
: Connect the red cable of the motorbike to the red terminal of
the battery.
DO NOT CONNECT BLACK CABLE TO RED TERMINAL OR RED CABLE TO BLACK TERMINAL!
8. Step H - Installing the licence plate- See Figure 24
: Attach the licence plate to its intended place at the back of the
motorbike body and press until you hear a click sound.
USE OF THE PRODUCT
Notice: When you change the direction of movement, first make sure that the motorbike is not in motion. Otherwise, if you
change the direction of movement suddenly without stopping the motorbike first, the gears and motor may get damaged.

See Figures 25 and 26: The ON/ OFF button is in the front body of the motorbike (Figure 26). And the The Forward
–
Stop - Backward button and the music panel are in the middle of the front body. The pedal is placed on the right side of the
body.
1.Moving forward - backward: Turn on the power of the motorbike. Press the button for
“▲ Forward – O - ▼ Back” in
position
“▲ Forward”. Press the pedal and the motorbike will start moving forward. Release the pedal and move to position
▼Back, and press the pedal, the motorbike will start moving backwards. Release the pedal and the motorbike will stop
moving.
2.The battery operated motorbike will stop automatically, when your child lifts its leg from the pedal.
3.Put the
▲O▼ button in position stop “O” and the motor will stop moving.
4.Music player (panel):
A.USB slot
–
only supports MP3.
B.AUX input
– Allows a cable to be connect to portable MP3 player or phone with the music player of the car
C. Increasing the volume
–
long press to turn the volume up.
D. Decreasing the volume
– long press in order to turn the volume down.
13
Do not put the MP3 player close to the ears and do not listen to loud music, because this may lead to
impairment of the hearing.