Mongoose MULTI SPEED Owner'S Manual Download

Page: 62 / 67

MAINTENANCE

Problem

Gear shifts not working properly

Slipping chain

Chain jumping off freewheel

sprocket or chainring

Constant clicking noises when pedaling

Possible Cause

• Derailleur cables sticking/

stretched/damaged

• Front or rear derailleur

not adjusted properly

• Indexed shifting not adjusted properly

• Excessively worn/chipped chainring

or freewheel sprocket teeth

• Chain worn/stretched

• Stiff link in chain

• Non compatible chain/

chainring/freewheel

• Chainring out of true

• Chainring loose

• Chainring teeth bent or broken

• Rear or front derailleur side-to-side

travel out adjustment

• Cross chaining and shifting under load

• Stiff chain link

• Loose pedal axle/bearing

• Loose bottom bracket axle/bearings

• Bent bottom bracket or pedal axle

• Loose crankset

Remedy

• Lubricate/tighten/replace cables

• Adjust derailleurs

• Adjust indexing

• Replace chainring,

sprockets and chain

• Replace chain

• Lubricate or replace link

• Seek advise at a bicycle shop

• Re-true if possible, or replace

• Tighten mounting bolts

• Repair or replace chainring/set

• Adjust derailleur travel

• Lubricate chain/adjust chain link

• Adjust bearings/axle nut

• Adjust bottom bracket

• Replace bottom bracket axle or pedals

• Tighten crank bolts

Summary of Contents for MULTI SPEED




































































Search results

Summary of Contents for MULTI SPEED

Reviews:

Related manuals for MULTI SPEED

Brands by name

Popular brands

Mongoose MULTI SPEED, Owner'S Manual

Search results

Summary of Contents for MULTI SPEED

Reviews:

Related manuals for MULTI SPEED

Brands by name

Popular brands