background image

34 

61D0006

FIREPLACE OPERATION 

ADVANTAGES OF A WOOD BURNING  
FIREPLACE

These are practical and ecological advantages of using wood 

as a fuel. Also to be considered is the aesthetic appeal. Most 

of us consider a wood fire with nostalgia. We enjoy the aroma 

and find the flickering light of a cozy hearth reminding us of 

things past. Wood has a low ash content. The little ash that 

remains after burning is useful in home gardening as a fertil-

izer and soil conditioner.

WHICH WOODS ARE BEST?

Each wood species offers something different in aroma or 

heat value. You should consider your needs and desires before 

building your fire.
Softwoods, like pine, spruce and fir are easy to ignite because 

they contain a lot of resin. However, a fire built entirely of 

softwoods burns out quickly. You also must add wood more 

often. While a softwood fire is not too desirable for a long 

evening, itʼs fine in the morning when you want quick warmth 

or late in the evening when you want a fire that will burn out 

before you go to bed.
On occasion when a longer fire is desired, itʼs best to combine 

softwoods with the heavier hardwoods such as ash, beech, 

birch, maple, oak and hickory. Hardwood burns slower, with 

shorter flames, and produce steady, glowing coals.
For the most pleasing aroma, burn the wood of fruit trees 

such as apple and cherry, or nut trees such as beech, hickory 

and pecan. This wood is generally more expensive, but a 

little combined with other wood goes a long way. Start your 

fire with a mixture of softwood and hardwood. Add some 

fruit or nut wood for nostalgic aroma. Since most woods 

will not burn well when freshly cut, the wood you purchase 

should be reasonably dry. Purchase logs that will fit when laid 

across your grate. Ask that the larger, heavier logs be split. 

Kindling should be short, easily split lengths of softwood, 

lumber yard or mill scraps, or twigs and branches gathered 

from your yard.

Fireplace damper must 
be fully opened when 
using a gas appliance. 

W

ARNING

See 

Gas  

Appliance 

Installation

 for 

more guidelines. 

HOW TO BUILD A BETTER FIRE

The first three fires should be of moderate size. This lets the 

fireplace adjust to the heat and the bricks to cure.
First, make sure your room is well ventilated, your damper 

open and the flue is unobstructed. Then make sure your wood 

is dry and seasoned. Unseasoned wood burns poorly. If you 

use unseasoned wood with poor ventilation or an obstructed 

chimney, smoking could occur. 
If your fireplace is equipped with an outside combustion air 

assembly, open the combustion air inlet by pushing upward 

on the lever located above the firebrick on the left side of the 

firebox.

Never  use  gasoline,  gasoline-type 
lantern fuel, kerosene, charcoal lighter 
fluid,  or  similar  liquids  to  start  or 
“freshen  up”  a  fire  in  this  fireplace. 
Keep all such liquids well away from 
the  fireplace  while  it  is  in  use.  Use 
of  this  fuel  can  cause  a  serious 
explosion.

W

ARNING

Prepare your fire by placing two logs on the iron grate or fire 

basket, and laying the tinder between them. Tinder may be 

dry scrap paper, twigs or bark. On top place a small hand-

ful of twigs or split softwood kindling. Place more dry logs 

over this base. Keep logs close together, as narrow air spaces 

between them promote better drafts. Heat reflected between 

adjacent surfaces aids in raising and maintaining combustion 

temperatures. 
Youʼll need a minimum of three logs, preferably four, to 

make a good fire. Add kindling and new logs as needed to 

rekindle a dying fire. New logs should be added at the rear 

grate after raking the coals toward the front. 

Note: Do Not 

Overfire the Fireplace. 

Overfire conditions happen when 

you use large amounts of kindling, building scraps or other 

improper fuels.
Ashes are important because they form a bed of glowing 

coals. Let ashes build up to 1" to 2" on the bottom of the 

grate. Excess ashes can be used to check a flaming fire or to 

“bank” your fire. Cover the logs with ashes. A “banked” fire 

will hold glowing coals for 8-10 hours, thereby saving a fire 

for later use.

Summary of Contents for 36" and 42" Wood Burning Fireplaces BWB400A













































Reviews: