MONARCH INSTRUMENT ACT-1B Series Instruction Manual Download Page 12

Page: 12 / 16

7.0 ACCESSORIES

See Accessories webpage for details.

Reflective Tape

T-5 (single pack), 5 feet - PN: 6180-070

T-5 (2-pack), 5 feet each - PN: 6180-069

T-50, 50 feet - PN: 6180-072

T-5WP (waterproof), 5 feet - PN: 6180-079

USB Programming Cable with PM Remote Software

Download the PM Remote Software from

monarchinstrument.com

. Use the USB Programming Cable

and software to change the ACT-1B settings or remotely

monitor the RPM

PN: 6180-031

ROLS-W Sensor:

Remote Optical Laser Sensor with 8 ft. cable

PN: 6180-030

ROS-W Sensor:

Remote Optical LED Sensor with 8 ft. cable

PN: 6180-056

ROS-P-25 Sensor:

Remote Optical LED Sensor with 25 ft. cable

(must cut off plug)

PN: 6180-057-25

ROS-HT-W-25 Sensor:

Remote Optical High-Temp Sensor with

25 ft. cable

PN: 6180-058-25

P5-11 Sensor:

Proximity Sensor with 10 ft. cable

PN: 6180-013

M-190W Sensor:

Magnetic Sensor with 10 ft. cable

PN: 6180-012

MT-190W Sensor:

Magnetic Trigger Sensor with amplifier

PN: 6180-037

GE-200HP Sensor:

Inductive Sensor with 15 ft. cable

PN: 6180-014

IRS-W Sensor:

Infrared Sensor with 8 ft. cable

PN: 6180-021

Summary of Contents for ACT-1B Series

















Search results

Summary of Contents for ACT-1B Series

Reviews:

Related manuals for ACT-1B Series

Brands by name

Popular brands

MONARCH INSTRUMENT ACT-1B Series, Instruction Manual

Search results

Summary of Contents for ACT-1B Series

Reviews:

Related manuals for ACT-1B Series

Brands by name

Popular brands