background image

AT2100 Air Head Crimp Tool 

Doc. No. 64005-1400 

Release Date: 12/09/02 

UNCONTROLLED COPY

 

Page 5 of 8 

Revision: C 

Revision Date:08-06-03 

 

Tool Calibration 

 
A Certificate of Calibration (see last page) was supplied with the tool.  To 
recalibrate this tool, pin gauge measurements should be taken in each 
conductor nest and compared to this chart.  The tool should be lubricated 
prior to recalibration to ensure consistent measurements. 
 
 
 
 
 

Wire Range 

“X” Dimension 

Conductor Crimp 

Nest Color Code 

AWG mm² 

Mean   Go 

No Go 

Crimp Inspection 

Marking 

14 - 16 

1.30 - 2.00 

.122 

.116 

.128 

o o 

16 – 20 HD  0.50 - 1.30 

.122 

.116 

.128 

o o 

Blue 

18 - 22* 

0.80 - 0.35 

.122 

.116 

.128 

o o 

* 18 - 22 End of step down butt splice only. 

 
 

Warranty 

 

This tool is for electrical terminal crimping purposes only.  This tool is made of the best quality materials. All vital components are 
long life tested.  All tools are warranted to be free of manufacturing defects for a period of

 30 days. 

  Should such a defect occur, 

we would repair or exchange the tool free of charge.  This repair or exchange will not be applicable to altered, misused or damaged 
tools. 

PIN GAUGE IN 

CONDUCTOR CRIMP

 

“Confining” Crimp 

 X  

Summary of Contents for AT 2100









Reviews: