background image

坐便器水效等级

1级

2级

3级

坐便器平均用水量

≤4.0

≤5.0

≤6.4

双冲坐便器全冲用水量

≤5.0

≤6.0

≤8.0

   

注意:每个水效等级中双冲坐便器的半冲平均用水量不大于其全冲用水量最大限定值的70%。

Water efficiency grades

Grade 1

Grade 2

Grade 3

Average water consumption

Full water consumption of 

dual flush

NOTE: For dual flush toilet, half flush water consumption shall not more than 70% of 

full flush water consumption.

用水效率等级

敬告:

本产品符合

GB25502

《坐便器用水效率限定值

及用水效率等级》规定,具体用水量及水效等级请看
粘贴在产品上的水效标识的标贴,其中水效等级划分
指标如下:

单位:升

Notice: This product complies with GB25502 “Limited value 

of toilet water efficiency and water efficiency grade”

. For 

the specific water consumption and water efficiency grades, 

please refer to the water efficiency label on the product. 

The water efficiency grade classification are shown in the 

table below.

Unit: Liter

Water Efficiency Grades

Symptoms

Operate push button correctly.

Probable Causes

Corrective Action

Dual flush fail 

Push button do not touch seat.

During fill cycle, hold float under water a few
seconds to allow it to fill with water ballast.

Valve float cup does not contain enough water
to provide required ballast.

Long or noisy tank fill
cycle

Clean the filter ofinlet valve.

Plugged valve inlet or supply line.

A. Adjust tank water level.

B. Unclog trapway; clean rim holes.

C. Clear obstruction from soil pipe or vent.

D. Open supply shut-off valve.

A. Water level is too low.

B. Trapway or rim holes are obstructed.

C. Soil pipe or vent is obstructed.

D. Supply shut-off valve not fully open.

Poor flush

A. Toilet trapway is obstructed.
B. Soil pipe or vent is obstructed.

A. Use plunger to unclog.
B. Clear obstruction from soil pipe or vent pipe.

Toilet overflows

Toilet does not activate

Reconnect the push button.

Push button is not connected to lift rod or

flush valve.

Fill valve continues to

run, allowing water to

enter tank

Incorrect water level

height

A. Valve float cup does not float in place.

B. Water replenishing pipe install in wrong way

.

C. Water leaking past drain valve.
D. Water level of fill valve height than overflow 

     hole.

A. Check fill valve float cup can move up and 

     down smothly, does not jam fault.
B. Install water replenishing pipe in right way 

    according to belowing diagram.

C. Ensure drain valve seal well.
D. Adjust fill valve water level to make sure lower  

    than overflow hole.

Troubleshooting Chart

Water level

Water replenishing pipe

Note: Water replenishing pipe shall above water level.

7

Summary of Contents for SW0311









Reviews: