Moeller 272557 Manual Download

Page: 41 / 51

Device Description

Touch-Panels for Industrial Automation

DVI-Panel

Maintenance and repair

02/05 AWB2720-1524GB

11 Maintenance and repair

Cleaning the screen

For trouble-free operation of the IR touch-screen, clean the inner section of
the device front (front glass and IR frame) regularly ( Section 8.3).

Repairs

Repairs to the DVI-Panels should only be carried out by the manufacturer or
Moeller GmbH repair centers. In this case, please contact your local
XSystem dealer or the Technical Support at Moeller GmbH. (manufacturer
address of DVI-Panel

Section 14)

No liability is accepted for any modifications made to the device that are not
described in this document.

Transport

Only the original packaging must be used for transporting the device. The
climatic conditions ( Section 12) has to be observed.

Storage

The device has to be stored under the conditions specified in Section 12.

It is recommended to store the device at room temperature.

Summary of Contents for 272557




















































Search results

Summary of Contents for 272557

Reviews:

Related manuals for 272557

Brands by name

Popular brands

Moeller 272557, Manual

Search results

Summary of Contents for 272557

Reviews:

Related manuals for 272557

Brands by name

Popular brands