manualshive.com logo in svg

Modellbau Lindinger Sukhoy 29S 30E ARF, Assembly Manual

Share
Download
Modellbau Lindinger Sukhoy 29S 30E ARF Assembly Manual Download Page 20

Modellbau Lindinger GmbH                 

     e-Mail: offi[email protected]          www.lindinger.at

 

20 

Decal set application 
 

   

   

 

 

    

 

 
 
Control throws

 

 
Please, follow carefully the recommended linkage setups for ailerons and elevators. 
 
For the AILERON we recommend the following throws: 
Low rate: 20° up / 20° down  

Expo: 40%  

3D rate:   45° up / 45° down  

Expo: 80% 

 
For the ELEVATOR we recommend the following throws: 
Low rate: 20° up / 20° down  

Expo: 25% 

3D rate:   60° up / 60° down  

Expo: 80% 

 
For the RUDDER we recommend the following throws: 
Low rate: 30° left / 30° right  

Expo: 30% 

3D rate:   50° left / 50° right  

Expo: 60% 

 
Note: the Expo is (+) for JR systems, and (–) for Futaba systems. 
 
 
Mixing 

 

For best performance, we recommend a linear-mix*:     

Rudder 

 Elevator UP

 

When you give full rudder to the right or left side, the elevator have to go up (positive) approx. 8%   
 
* if you have a programmable computer radio. 

Summary of Contents for Sukhoy 29S 30E ARF






















Reviews:

No comments

Brands by name

Popular brands

Load more brands