Mobeye ThermoGuard CM4200 User Manual Download Page 4

Attention! Very important 

 
This user manual contains important guidelines for the installation and usage of 
the Mobeye

® 

device as described in this manual. Please read these thoroughly 

before you start using the Mobeye

® 

device. 

In the case of damage caused by disregarding the guidelines and the instructions 
for  use,  no  liability  is  accepted  and  the  warranty  becomes  void.  The  user  must 
regularly check the proper functioning of the Mobeye

®

 device. The manufacturer 

cannot  be  held  liable  for  (direct  and  indirect)  damage  as  a  result  of  incorrect 
operation  or  incorrect  functioning  of  the  device,  software,  internet  or  telecom 
connection.  The  manufacturer  is  in  no  way  liable  for  the  loss  of  personal 
passwords or codes. 
 

Safety guidelines 

• 

 The  permitted  ambient  temperature  during  operation  may  not  be  exceeded 

(not lower than -10 °C and not higher than 50 °C). 

• 

 The device is intended for use in dry and clean places. 

• 

 Protect the device from moisture, heat and water splashing. Not intended for 

external use. 

• 

 The guidelines for the battery usage must be regarded.  

• 

 Do not expose the device to strong vibrations. 

• 

 Do not let it fall from height. 

• 

 Do not use in an environment where any inflammable gases, vapors or dust are 

present or could be present.  

• 

 Repair of the device may only be carried out by people, trained for Mobeye

®

 

repair. 

• 

 If the device must be repaired, only original replacement components may be 

used. The use of different parts may lead to damage of the Mobeye

®

 device. 

 

Use in accordance with the regulations 

The purpose of this device in accordance with the regulations is sending messages 
and making telephone calls after an alarm situation. Other uses are not permitted 
and may invalidate the warranty. 
 

Battery recycling 

This product contains recyclable components. When disposing of this product, 
please take it to a waste collection point for disposal or to your sales point. Bring 
empty batteries to a recycling centre or collection point. 

Summary of Contents for ThermoGuard CM4200

































Reviews: