INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
WALL1 / WALL2 / WALL3
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•
This product is Class I and must be earthed
•
This product series is IP65 rated
INSTALLATION
•
Provide power to the required point of installation (refer to BS7671 for correct cabling methods).
Suitable IP rated junction boxes should be used where required
•
Using the Allen key provided, carefully loosen the three grub screws securing the baseplate to the
luminaire (see Fig. 1)
Fig. 1
•
Using the baseplate as a template, mark the location for, and drill the fixing holes ensuring not to
infringe with any gas / water pipes or electrical cables
•
Feed the mains cable through the rubber grommet to retain IP rating, and secure the baseplate using
the screws provided
•
Connect the luminaire to the mains supply ensuring that correct polarity is observed (see Fig. 2): L -
Live (brown), E - Earth (green/yellow), N - Neutral (blue)
Fig. 2
•
Replace the luminaire onto the baseplate and fasten the three grub screws
•
Unscrew the bezel, insert a suitable GU10 lamp and carefully replace the bezel ensuring that the seal
is in place and not damaged
•
Switch on and check for correct operation
Loosen grub screws
Fig. 1
• Using the baseplate as a template, mark the location for, and drill the fixing holes ensuring not to infringe
with any gas / water pipes or electrical cables
• Feed the mains cable through the rubber grommet to retain IP rating, and secure the baseplate using the
screws provided
• Connect the luminaire to the mains supply ensuring that correct polarity is observed (see Fig. 2):
L - Live (brown), E - Earth (green/yellow), N - Neutral (blue)
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
WALL1 / WALL2 / WALL3
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•
This product is Class I and must be earthed
•
This product series is IP65 rated
INSTALLATION
•
Provide power to the required point of installation (refer to BS7671 for correct cabling methods).
Suitable IP rated junction boxes should be used where required
•
Using the Allen key provided, carefully loosen the three grub screws securing the baseplate to the
luminaire (see Fig. 1)
Fig. 1
•
Using the baseplate as a template, mark the location for, and drill the fixing holes ensuring not to
infringe with any gas / water pipes or electrical cables
•
Feed the mains cable through the rubber grommet to retain IP rating, and secure the baseplate using
the screws provided
•
Connect the luminaire to the mains supply ensuring that correct polarity is observed (see Fig. 2): L -
Live (brown), E - Earth (green/yellow), N - Neutral (blue)
Fig. 2
•
Replace the luminaire onto the baseplate and fasten the three grub screws
•
Unscrew the bezel, insert a suitable GU10 lamp and carefully replace the bezel ensuring that the seal
is in place and not damaged
•
Switch on and check for correct operation
Loosen grub screws
Fig. 2
