INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
T8BLED15EM1 / T8BLED16EM1 / T8BLED25EM1 / T8BLED26EM1
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•
This product is for indoor use only
•
This product is Class I and must be earthed
•
This product is IP20 rated
INSTALLATION
Note - If this product is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED luminaires.
•
Provide power to the required point of installation
•
Remove the two end caps with the aid of a flat screwdriver
•
Single luminaire: squeeze the sides of the fitting together to separate the LED plate from the housing
•
Twin luminaire: remove the two screws (see Fig. 1) and slide the LED plate away from the housing
Fig. 1
•
Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas / water
pipes or electrical cables. The fitting can also be mounted over conduit boxes, the distance between
fixing centres is 60cm
•
Feed the mains cable into the luminaire either through the rear, or by drilling the end cap and using a
20mm compression gland (not included)
•
Secure the luminaire to the surface
•
Ensuring correct polarity is observed, carefully wire as shown in Fig. 2
Fig. 2
• Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas / water pipes or
electrical cables. The fitting can also be mounted over conduit boxes, the distance between fixing centres is
60cm
• Feed the mains cable into the luminaire either through the rear, or by drilling the end cap and using a 20mm
compression gland (not included)
• Secure the luminaire to the surface
• Ensuring correct polarity is observed, carefully wire as shown in Fig. 2
Fig. 1
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
T8BLED12 / T8BLED14 / T8BLED15 / T8BLED15HL / T8BLED16 / T8BLED16HL / T8BLED22 / T8BLED24 /
T8BLED25 / T8BLED25HL / T8BLED26
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•
This product is for indoor use only
•
This product is Class I and must be earthed
•
This product is IP20 rated
INSTALLATION
Note - If this product is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED luminaires.
•
Provide power to the required point of installation
•
Remove the two end caps with the aid of a flat screwdriver
•
Single luminaire: squeeze the sides of the fitting together to separate the LED plate from the housing
•
Twin luminaire: remove the two screws (see Fig. 1) and slide the LED plate away from the housing
Fig. 1
•
Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas / water
pipes or electrical cables. The fitting can also be mounted over conduit boxes, the distance between
fixing centres is 60cm
•
Feed the mains cable into the luminaire either through the rear, or by drilling the end cap and using a
20mm compression gland (not included)
•
Secure the luminaire to the surface
•
Ensuring correct polarity is observed, carefully wire as shown in Fig. 2
Fig. 2
•
Check the earth tab connection is in place and reconnect if required
Fig. 2
