BTxxACTS
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following products:
BT9ACTS / BT14ACTS / BT20ACTS
SAFETY
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•
Please isolate mains prior to installation or maintenance
•
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating
of the circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
•
This product is Class II double insulated
•
This product is IP65 rated
INSTALLATION
Note - Microwave sensors may not be suitable for all installations, for example enclosed spaces, as they are able
to detect movement through non-metallic surfaces like plasterboard and thin doors.
•
Provide power to the required point of installation. Suitable IP rated junction boxes should be used
where required
•
Remove the diffuser by rotating bezel anti-clockwise (see Fig. 1)
Fig. 1
Fig. 2
•
Remove the fastening screw securing the LED plate and open the LED plate (see Fig. 2)
•
Mark the location of the fixing holes, and drill the holes ensuring not to infringe with any gas/water
pipes or electrical cables
•
Feed the cable via the rubber grommet to retain IP rating, and secure the baseplate to the surface
•
Connect the Live (brown) and Neutral (blue) to the terminals on the terminal block (see Fig. 3)
Fig. 3
•
Refasten the LED plate screw
•
Choose the required colour temperature by means of the DIP switch (see Fig. 6)
Fig. 6
•
Reattach the diffuser by rotating clockwise
•
Switch on and check for correct operation, ensuring the green indicator LED is illuminated
•
We recommend, on commissioning the installation, a minimum charge period of 24 hours before
carrying out an emergency duration test
Note: this fitting shuts off power to the Lithium Ion battery periodically to prevent overcharging.
Therefore, the green LED indicator has been set up to indicate that the emergency inverter is in good
condition, not to indicate that the battery is charging. The installer must ensure that the battery is
connected.
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
The batteries in this luminaire are Lithium Ion and must be disposed of correctly. Please contact the local
authorities for the disposal of this toxic waste.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is non-dimmable.
WARRANTY
This product has a warranty of 5 years (excluding battery) from date of purchase. Failure to install this product in
accordance with the current edition of the IEE Wiring Regulations, improper use, or removal of the batch codes
will invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve the
right to alter product specification without prior notice.
TESTING FOR EMERGENCY LUMINAIRES
Recommended routine test procedure in accordance with BS5266
•
Daily check
–
check LED charge indicator is illuminated
•
Monthly functional test
–
simulate a mains supply failure for approx. 30 seconds by operation of key
switch or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge
indicator is illuminated
•
Annual 3-hour duration test
- simulate a mains supply failure for a 3-hour continuous test by operation of
key switch or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge
indicator is illuminated
•
If the luminaire fails any of the above tests, please contact a qualified electrician
• The additional terminal called Slave Live (L’) is available to enable the sensor to power on
additional luminaires. A max. LED load of 400W can be controlled by the sensor
• Please see DIP Switch Layout to set up sensor
• Refasten the LED plate screw
• Choose the required colour temperature by means of the DIP switch (see Fig. 4)
Fig. 3
Fig. 4
