background image

6

Before using this equipment!

Thoroughly read and understand the instructions given in this manual before operation. 

Refer to the safety decal section and read all instructions noted to them.

Do not allow anyone to operate this implement who has not fully read and comprehend

-

ed this manual and who has not been properly trained in the safe operation of the imple

-

ment. 

Review operator’s manual annually.

Be sure that you know the dangers and safety concerns while operating this equipment!
Understand that your safety and the safety of other persons are measured by how you service 

and operate this machine.

The safety information given in this manual does not replace safety codes,federal,state or local 

laws. Make certain your machine has the proper equipment as designed by local laws and reg-

ulations.

Warning!

 

Operator should be a responsible adult.

 Do not allow persons to operate or assemble this 

unit until they have developed a thorough understanding of safety precautions and how it works.

• 

Do not use this machine while under the influence of drugs or alcohol.

• 

The operator should be familiar with all functions of the tractor and attached implement, and be 

able to handle emergencies quickly.

• 

Keep hands, feet, and clothing away from power-driven parts.

• 

Do not wear loose-fitting clothing which may catch moving parts.

• 

 Always wear protective clothing and substantial shoes.

• 

 It is recommended that hearing and eye protection be worn

.

• 

Make sure all guards and shields are in place and secured before operating implement.

• 

Keep all bystanders, especially small children away from equipment and work area be

-

fore starting.

• 

Place all controls in neutral, stop tractor engine, set park brake, remove ignition and wait for all 

moving parts to stop before servicing, adjusting, repairing or unplugging the cutter.

• 

Place all tractor controls in neutral before starting.

• 

Start tractor and operate controls from the driver’s seat only. Never from the ground

.

• 

Do not operate the tractor inside a building unless there is adequate ventilation.

• 

Never dismount from a moving tractor or leave tractor unattended with engine running.

• 

Never adjust, service, clean, or lubricate implement until all power is shut off.

Safety -- It’s in your interest!

Summary of Contents for Pulsar Wing









































Reviews: