Mitsubishi QJ71NT11B User Manual Download Page 16 | Manualshive

Page: 16 / 24

background image

9

5.1 Twisted Bus System (When using twisted pair cable)
5.1.1 Specifications of twisted pair cable

The following shows the specifications of a shielded twisted pair cable used in
the twisted bus system.
Twisted pair cables that satisfy the following specifications can also be used
even not introduced.

Item KNPEV-SB

0.5SQ

1P*1

Cross section

Cable

Shielded twisted pair cable

Core 2-core
Conductor
resistance (20 )

39.4 /km or less

Insulation resistance
(20 )

10M km or more

Dielectric withstand
voltage V-min

1000VAC 1 minute

Capacitance
(1kHz)

70nF/km or less on average

Characteristic
impedance
(100kHz)

110 10

*1: Applicable only when the communication speed is 1.25Mbps or less.

«
...
14
15
16
17
18
...
»

Summary of Contents for QJ71NT11B

























Reviews:

No comments

Related manuals for QJ71NT11B

Brand: Zetkama Pages: 6

Brand: Facility Explorer Pages: 4

Brand: ZIGBEE Pages: 5

Brand: UNICORECOMM Pages: 32

Brand: UNICORECOMM Pages: 7

Brand: UNICORECOMM Pages: 26

Brand: UNICORECOMM Pages: 25

Brand: IBC Pages: 8

Brand: Newport Pages: 417

Brand: Matelec Pages: 16

MT600iWP Series

Brand: weintek Pages: 2

Brand: PS Automation Pages: 4

Brand: Objective Imaging Pages: 11

Brand: Festo Pages: 62

Brand: GE Pages: 32

SYSVRF AHU 10HP S

Brand: SystemAir Pages: 16

Brand: Zapi Pages: 30

Brand: MERCATOR Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands