manualshive.com logo in svg

Mitsubishi MFZ-KA-VA, Service Technical Manual, Page: 30 / 74

Share
Download
Mitsubishi MFZ-KA-VA Service Technical Manual Download Page 30

30

EMERGENCY OPERATION switch

E.O.

SW

Operation mode

COOL

HEAT

Set temperature

24

:

24

:

Fan speed

Medium

Medium

Horizontal vane

Auto

Auto

The operation mode is indicated by the Operation
Indicator lamp on the indoor unit as following

Operation indicator lamp

Press again <Heat>

Press once <Cool>

Press once again <Stop>

Not lighted

Lighted

2-9. EMERGENCY/TEST OPERATION

In case of test run operation or emergency operation, use EMERGENCY OPERATION switch on the front of the indoor
unit. Emergency operation is available when the remote controller is missing, has failed or the batteries of the remote 
controller run down. The unit will start and OPERATION INDICATOR lamp will light.
The first 30 minutes of operation is the test run operation. This operation is for servicing. The Indoor fan speed runs at
High speed and the system is in continuous operation (The thermostat in ON).
After 30 minutes of test run operation the system shifts to EMERGENCY COOL / HEAT MODE with a set temperature of
24°C. The fan speed shifts to Med..
The coil frost prevention works even in emergency operation, and defrosting too.
In the test run or emergency operation, the horizontal vane operates in VANE AUTO (

) mode.

Emergency operation continues until EMERGENCY OPERATION switch is pressed once or twice or the unit receives any
signal from the remote controller. In case of latter normal operation will start.

NOTE : Do not press EMERGENCY OPERATION switch during normal operation.

PROGRAM TIMER

(Example 1) The current time is 8:00 PM.

The unit turns off at 11:00 PM, and on at 6:00 AM.

• OFF timer and ON timer can be used in combination. The timer of the set time that is reached first will operate first.
• “

” and “

” display shows the order of OFF timer and ON timer operation.

(Example 2) The current time is 11:00 AM.

The unit turns on at 5:00 PM, and off at 9:00 PM.

NOTE :  If the main power is turned off or a power failure occurs while AUTO START/STOP timer is active, the timer setting is

cancelled. As these models are equipped with an auto restart function, the air conditioner starts operating with timer
cancelled when power is restored.

OBT14A--1qxp  06.1.12 1:07 PM  Page 30

Downloaded from AC-Manual.com Manuals

Summary of Contents for MFZ-KA-VA











































































Reviews:

No comments